VistaQuest N7227V5 ユーザーズマニュアル
– 73 –
Section 16. SYSTEM OPERATION
Security Codes
Installer Code
The installer programs the 4-digit Installer Code initially as part of the
programming procedure. The factory default Installer code is "4-1-1-1", but
may be changed in field
programming procedure. The factory default Installer code is "4-1-1-1", but
may be changed in field
✱
20. Note: The Installer Code is defined as User #1.
The Installer code is the only code that can allow re-entry into programming
mode. In normal operation mode, only the Master code can be used to enter
the User codes (refer to
mode. In normal operation mode, only the Master code can be used to enter
the User codes (refer to
Assigning the Master Code).
See
MECHANICS OF PROGRAMMING section in the PROGRAMMING
GUIDE manual for details on exiting the programming mode via
✱
98 or
✱
99.
Assigning the
Master Code
In normal operation mode, assign the 4-digit Master Code as follows:
Installer Code + 8 + 2 + 4-digit Master Code
Note: The Master Code is defined as User #2.
Changing the
Master Code
In normal operation mode, the Master code can be changed by entering:
Master Code + 8 + 2 + New Master Code + New Master Code again
User Codes
In normal operation mode, the Master security code can be used to assign up
to 4 secondary 4-digit security codes. It can also be used to remove sec -
ondary codes from the system (individually).
to 4 secondary 4-digit security codes. It can also be used to remove sec -
ondary codes from the system (individually).
To assign (or change) a Secondary security code, enter (via keypad) :
Master Code + [CODE key] + User # (3–6) + desired 4-digit Secondary Code
The system will emit a single beep when each secondary code has been suc -
cessfully entered.
cessfully entered.
To delete a Secondary security code, enter (via keypad) :
Master Code + [CODE key] + User # (3–6)
Notes:
•
All Master and Secondary security codes permit ac cess to the system for
arming, dis arming, etc.
arming, dis arming, etc.
•
If a secondary code is inadvertently re peated for differ ent users, the lower
user number will take priority.
user number will take priority.
•
Opening and closing reports are sent for the Master code as No. 02, with
the appropriate subscriber number. Secondary user codes are sent as Nos.
3 through 6 respectively, with the appropri ate subscriber number.
the appropriate subscriber number. Secondary user codes are sent as Nos.
3 through 6 respectively, with the appropri ate subscriber number.
Duress Code
Important: This code is
useful only when the
system is connected to a
central station.
useful only when the
system is connected to a
central station.
This feature is intended for use when you are forced to disarm or arm the
system under threat. When used, the system will act normally, but can silently
notify the central station of your situation, if that service has been provided.
The Duress code may be any 4-digit code assigned to User Number 8.
To program a Duress code:
1.
system under threat. When used, the system will act normally, but can silently
notify the central station of your situation, if that service has been provided.
The Duress code may be any 4-digit code assigned to User Number 8.
To program a Duress code:
1.
Enter Master Code.
2.
Press the CODE [8] key.
3.
Press the [8] key again (8 = Duress code User No.).
4.
Enter the desired 4-digit Duress Code. The keypad will beep once.
Note:
Note:
The Duress code must differ from the Master Code or any other
User’s Code.
User’s Code.
To change the Duress code :
Repeat steps 1, 2, and 3, and then step 4 with the new Duress Code.
Repeat steps 1, 2, and 3, and then step 4 with the new Duress Code.
To delete the Duress code:
Perform steps 1, 2, and 3, and then stop. When the keypad beeps once it
signifies that the code has been deleted.
Perform steps 1, 2, and 3, and then stop. When the keypad beeps once it
signifies that the code has been deleted.