Siemens AT Command Set Cellular Engines Wireless Modules MC35 ユーザーズマニュアル
AT Command Set
MC35_ATC_01_V04.00
Page 63 of 238
02.04.2002
<class>
integer or sum of integers each representing a <class> of informa-
tion:
1
tion:
1
voice
2
data
4
fax
8
short message service
16
data circuit sync
32
data circuit async
64
dedicated packet access
128
dedicated PAD access
x
combination of some of the above classes.
For example, the default setting 7 represents the sum of
the integers 1, 2 and 4 (CF for voice, data and fax). The
value 255 covers all classes. If the <class> parameter is
omitted, the default value 7 is used.
For example, the default setting 7 represents the sum of
the integers 1, 2 and 4 (CF for voice, data and fax). The
value 255 covers all classes. If the <class> parameter is
omitted, the default value 7 is used.
<time> time to wait before call is forwarded, rounded to a multiple of 5 sec..
1...20..30 (only for <reas>=no reply)
<status> 0 not active
1 active
Reference
GSM 07.07,
GSM 02.04,
GSM 02.82
GSM 02.04,
GSM 02.82
Note
• Please note that you can register, disable, enable and erase <reas>
4 and 5 as described above. However, it is not possible to query the status
of <reas> 4 and 5 with AT+CCFC. Instead, you may use the the ATD
command followed by *'# codes to check the status of these two reasons.
See Chapter 9.4 for a complete list of *# GSM codes. See also examples
below.
of <reas> 4 and 5 with AT+CCFC. Instead, you may use the the ATD
command followed by *'# codes to check the status of these two reasons.
See Chapter 9.4 for a complete list of *# GSM codes. See also examples
below.
• The AT+CCFC command offers a broad range of call forwarding options
according to the GSM specifications. However, when you attempt to set a
call forwarding option which is not provisioned or not yet subscribed to, the
setting will not take effect regardless of the response returned. The re-
sponses in these cases vary with the network (for example “OK”, “Opera-
tion not allowed”, “Operation not supported” etc.). To make sure check the
the call forwarding status with <mode>=2.
call forwarding option which is not provisioned or not yet subscribed to, the
setting will not take effect regardless of the response returned. The re-
sponses in these cases vary with the network (for example “OK”, “Opera-
tion not allowed”, “Operation not supported” etc.). To make sure check the
the call forwarding status with <mode>=2.
4.6.1 Examples: Call forwarding
Please note that when you configure or query call forwarding without specifying any classes, the set-
tings will refer to classes 1, 2 and 4 only (=default). The handling of classes is equivalent to AT+CLCK
(Chapter 4.21.3).
tings will refer to classes 1, 2 and 4 only (=default). The handling of classes is equivalent to AT+CLCK
(Chapter 4.21.3).
Example 1
To register the destination number for unconditional call forwarding (CFU):
at+ccfc=0,3,"+493012345678",145
at+ccfc=0,3,"+493012345678",145
OK
Remember that call forwarding will be activated for voice, data and fax (de-
fault classes) when you register the destination number.
fault classes) when you register the destination number.
Example 2
To query the status of CFU without specifying <class>:
at+ccfc=0,2
at+ccfc=0,2
+CCFC: 1,1,"+493012345678",145