Siemens AT Command Set Cellular Engines Wireless Modules MC35 ユーザーズマニュアル
AT Command Set
MC35_ATC_01_V04.00
Page 71 of 238
02.04.2002
6
CYCLIC SLEEP mode:
AT+CFUN=6 disconnects any circuit-switched call in prog-
ress, but has no effect on a GPRS call. The ME goes into
the power saving mode 10 minutes after the last character
was transmitted over the serial interface. Sending charac-
ters over the serial interface resets the timer.
The first wake-up event stops power saving. Also, you can
enter AT+CFUN=1 to terminate power saving.
AT+CFUN=6 disconnects any circuit-switched call in prog-
ress, but has no effect on a GPRS call. The ME goes into
the power saving mode 10 minutes after the last character
was transmitted over the serial interface. Sending charac-
ters over the serial interface resets the timer.
The first wake-up event stops power saving. Also, you can
enter AT+CFUN=1 to terminate power saving.
<rst>
0
The <rst> parameter can only be used if +CFUN=1, 5 or 6.
Due to the command syntax, you need to enter <fun>,
followed by <rst>, where <fun> is only a placeholder and
has no effect. See examples below.
Due to the command syntax, you need to enter <fun>,
followed by <rst>, where <fun> is only a placeholder and
has no effect. See examples below.
1
ME resets and restarts to full functionality.
After reset and restart, PIN 1 authentication is necessary.
Therefore, you are required to use AT+CPIN again. If
autobauding is enabled it is recommended to wait 3 to 5
seconds before entering the first AT command. For details
on autobauding refer to Chapter 2.45.1
After reset and restart, PIN 1 authentication is necessary.
Therefore, you are required to use AT+CPIN again. If
autobauding is enabled it is recommended to wait 3 to 5
seconds before entering the first AT command. For details
on autobauding refer to Chapter 2.45.1
Reference
GSM 07.07
Note
• In multiplex mode, the CFUN profile is shared by all multiplexer channels.
When you change the CFUN state on one logical channel, all other logical
channels adopt the same state.
channels adopt the same state.
Example 1
To check the level of functionality use the read command:
AT+CFUN?
AT+CFUN?
+CFUN: 1
Default mode after ME was restarted.
Remember that the AT interface is not accessible in NON-CYCLIC SLEEP
mode. Consequently, the read command is only useful when the ME is set to
full functionality or, when <fun> is set to 5or 6.
mode. Consequently, the read command is only useful when the ME is set to
full functionality or, when <fun> is set to 5or 6.
AT+CFUN?
+CFUN: 5
CYCLIC SLEEP mode.
Example 2
To set the ME to NON-CYCLIC SLEEP mode enter
AT+CFUN=0
AT+CFUN=0
OK
When, for example, an SMS is being received and indicated by an unsolicited
result code (URC), the ME wakes up to full operation.
+CMTI: "SM",5
result code (URC), the ME wakes up to full operation.
+CMTI: "SM",5
Note that the URC used in this example will appear
only if CMTI=1,1 was configured before. See Chapters
5.10 and 9.1.4.
only if CMTI=1,1 was configured before. See Chapters
5.10 and 9.1.4.
After this, you may want to verify the operating status:
AT+CFUN?
AT+CFUN?
+CFUN: 1
Indicates that ME has entered full functionality mode.
Example 3
To enable CYCLIC SLEEP mode, level 6:
AT+CFUN=6
AT+CFUN=6
OK