Siemens AT Command Set Cellular Engines Wireless Modules MC35 ユーザーズマニュアル
AT Command Set
MC35_ATC_01_V04.00
Page 79 of 238
02.04.2002
4.21 AT+CLCK Facility lock
Test command
AT+CLCK=?
Response
+CLCK: (list of supported <fac>s) OK
Parameter
See execute command
Execute command
AT+CLCK=<fac>,
<mode>
[,<passwd>
[,<class>]]
<mode>
[,<passwd>
[,<class>]]
Use this command to lock, unlock or interrogate a ME or a network facility
<fac>. The command can be aborted when network facilities are being set or
interrogated.
<fac>. The command can be aborted when network facilities are being set or
interrogated.
Response
If
<mode>
≠ 2 and command is successful
OK
If
<mode> = 2 and command is successful
+CLCK: <status>[,<class1>[<CR><LF>
+CLCK: <status>, class2....]] OK
+CLCK: <status>, class2....]] OK
If error is related to ME functionality:
+CME ERROR: <err>
+CME ERROR: <err>
Parameter
<fac> Phone security locks set by client or factory:
“SC” SIM (lock SIM cards). SIM requests password upon ME power-
up and when this lock command is issued. "SC" lock is protected
with SIM PIN1. The number can be modified with AT+CPWD or
AT^SPWD. See examples in Chapter 4.21.2 for further explana-
tions.
with SIM PIN1. The number can be modified with AT+CPWD or
AT^SPWD. See examples in Chapter 4.21.2 for further explana-
tions.
“PS” Phone locked to SIM card. ME requests password when other
than current SIM card is inserted.
If set individually by the client, the password for the "PS" lock
can be specified with AT+CPWD or AT^SPWD.
If set by factory (e.g. for a prepaid mobile), the password is sup-
plied by the provider or operator.
If set individually by the client, the password for the "PS" lock
can be specified with AT+CPWD or AT^SPWD.
If set by factory (e.g. for a prepaid mobile), the password is sup-
plied by the provider or operator.
“FD” SIM fixed dialling memory: If the mobile is locked to "FD", only
the phone numbers stored to the "FD" memory can be dialled
(depending on the SIM card, usually up to 7 numbers). If PIN2
authentication has not been performed during the current ses-
sion, PIN2 is requested as <passwd>.
(depending on the SIM card, usually up to 7 numbers). If PIN2
authentication has not been performed during the current ses-
sion, PIN2 is requested as <passwd>.
"CS" Keypad lock (not supported since keypad cannot be directly
connected to the GSM engine)
Note:
Primarily intended for the client to take safety precautions, "SC",
"PS" and "FD" can be configured individually. "PS" may also be
factory set.
"PS" lock is frequently referred to as "phone lock", or "device
lock". Accordingly, the password may be called "phone code" or
"device code". The "PS" password is not associated with the
PUK of the SIM card. If incorrectly entered three times, the
Master Phone Code is required to lift the lock. Once the Master
Phone Code has been acctepted, the mobile is operational, and
the "PS" lock is no longer active. If needed it must be set once
again. See Chapter 4.35.1 and examples below for further de-
tails.
factory set.
"PS" lock is frequently referred to as "phone lock", or "device
lock". Accordingly, the password may be called "phone code" or
"device code". The "PS" password is not associated with the
PUK of the SIM card. If incorrectly entered three times, the
Master Phone Code is required to lift the lock. Once the Master
Phone Code has been acctepted, the mobile is operational, and
the "PS" lock is no longer active. If needed it must be set once
again. See Chapter 4.35.1 and examples below for further de-
tails.