Manualsbrain.com
  1. マニュアル
  2. ブランド
  3. Tascam
  4. CD-RW2000
  5. ユーザーズマニュアル

Tascam CD-RW2000 ユーザーズマニュアル

ダウンロード
ページ / 32
3 – Playback operations—CALL playback
 TASCAM CD-RW2000 
17
3.4 CALL playback
The 
CALL
 keys (
L
 and 
K
) allow the unit’s play-
back position to be returned to the point at which 
playback last started from pause mode. If there is no 
“call point” (i.e. playback starting from pause), 
pressing the 
CALL
 key will have no effect. It should 
also be noted that this call function is available in 
play and pause modes only.
Note that the call mode is not available when shuffle 
mode has been selected (see 3.1.3, “Playback 
modes”) and there is no “call point” set.
3.5 Auto Ready function
This function allows the playing back of a single 
track, and the automatic cueing of the next track 
ready for playback.
The unit is cued to the start of the track as determined 
by the subcode, not the start of the audio signal, 
unless the 
AUTO CUE
 function is on (see 3.6, “Auto 
Cue function”).
The unit will enter pause mode in the continue, shuf-
fle and programmed play modes, after the location 
has taken place.
If repeat is active (see 3.3, “Repeat play”), the unit 
will enter play ready mode at the start of the next 
track (
REPEAT ALL
), or the start of the track which is 
being repeated (
REPEAT 1
).
To set the function:
1
Repeatedly press the 
MENU
 key (
9
 or 
6
) 
until the display shows 
A_READY>XXX 
where 
XXX
 is either 
ON
 or 
OFF
.
2
Use the 
MULTI DIAL
 control 
B
 or the 
 SKIP
 
keys 
H
 to set the function to 
ON
.
When the function is on, the 
A-READY
 display 
indicator is lit.
3.6 Auto Cue function
The Auto Cue function allows you to set up the unit 
so that when a track is selected for playback in pause 
mode (cued), playback will start, not at the first posi-
tion of the track as indicated by the subcode, but at 
the first position of the track where the audio level 
exceeds a set trigger level.
The trigger level is the same as the recording trigger 
level, as set in 4.3.1, “Synchronized recording”. Con-
sult this section on how to set the trigger level.
To set the Auto Cue function on:
1
Repeatedly press the 
MENU
 key (
9
 or 
6
) 
until the display shows 
A_CUE > XXX 
where 
XXX
 is either 
ON
 or 
OFF
.
2
Use the 
MULTI DIAL
 control 
B
 or the 
 SKIP
 
keys 
H
 to set the function to 
ON
.
When the function is on, the 
A-CUE
 display indi-
cator is lit.
NOTE
When using the Auto Cue function, there may be a 
short “click” sound output through the DIGITAL 
COAXIAL and OPTICAL OUT terminals (
X
 and 
Y
) 
as the unit locates to the audible start of the track just 
before it enters pause mode. However, this sound will 
not be output through the DIGITAL AES/EBU OUT 
terminal 
W
.
3.7 Incremental play
Incremental playback means that when the 
STOP
 key 
G
 or 
I
 is pressed (or if a STOP signal is received 
through the 
CONTROL 
connector 
T
) while a track 
is being played back, the playback position will be at 
the start of the next track.
If the 
PLAY
 key 
H
 is pressed while the incremental 
playback mode is on, playback starts from the start of 
the next track.
To set the incremental play mode on:
1
Repeatedly press the 
MENU
 key (
9
 or 
6
) 
until the display shows 
INC PLAY>XXX 
where 
XXX
 is either 
ON
 or 
OFF
.
2
Use the 
MULTI DIAL
 control 
B
 or the 
 SKIP
 
keys 
H
 to set the function to 
ON
.
Although there is no indication when the incre-
mental play mode is selected, you will notice 
that is in operation whenever you stop play-
back of a track.