Manualsbrain.com
  1. マニュアル
  2. ブランド
  3. Tascam
  4. CD-RW2000
  5. ユーザーズマニュアル

Tascam CD-RW2000 ユーザーズマニュアル

ダウンロード
ページ / 32
5 – After recording—Erasing
 TASCAM CD-RW2000 
29
3
Turn the 
MULTI DIAL
 control or use the 
 SKIP
 
keys to change the number of the first track to 
be erased. The highest value that this number 
can take is the last track recorded (e.g. if 17 
tracks have been recorded on the disc, 
17-
17
 means that the last track only, 17, will be 
erased). The lowest value that this number can 
take is 
2
 (if this number was 
1
, the whole disc 
would be erased, as described below).
4
If you do not want to proceed with the erase 
operation, press any other key (such as the 
STOP
 key).
NOTE
If only one track has been recorded on the disc, only 
the “erase disc” option (5.2.2, “Erasing a whole disc”) 
is available.
5
When the range of tracks to be erased has been 
selected, press the 
MULTI DIAL
 control or press 
the 
ENTER
 key 
7
.
NOTE
This operation cannot be undone. If you are going to 
erase a track or tracks, make sure that they are 
recordings that you really want to erase!
6
If the erase operation has been selected, the 
word 
ERASE
 flashes on the display, and the 
timer starts counting down. The process will 
typically take around 20 seconds).
7
At the end of the countdown period, the word 
Complete
 appears briefly on the display, 
and the display returns to the track/time 
display.
5.2.2
Erasing a whole disc
When you want to erase a whole disc (all the tracks 
on a disc), follow the procedure below:
1
With the disc loaded, and the unit in stop 
mode, press the 
ERASE
 key (
F
 or 
C
).
2
Turn the 
MULTI DIAL
 control 
B
 or use the 
 
SKIP
 keys 
H
 until the display shows 
ERASE 
DISC?
.
3
If you do not want to proceed with the erase 
operation, press any other key (such as the 
STOP
 key).
4
To erase the contents of the disc, press the 
MULTI DIAL
 control or press the 
ENTER
 key 
7
.
NOTE
This operation cannot be undone. If you are going to 
erase a disc, make sure that it contains only record-
ings that you really want to erase!
5
If the erase operation has been selected, the 
word 
ERASE
 flashes on the display, and the 
timer starts counting down a time value shown 
on the display.
6
At the end of the countdown period, the word 
Complete
 appears briefly on the display, 
and the display returns to the track/time 
display.
5.2.3
Refreshing a disc
If a CD-RW disc has been corrupted at any point (e.g. 
power has been cut off in the middle of a finalize 
operation, etc.), or has been used in a computer or 
another piece of equipment that makes it unreadable, 
it is possible to “refresh” the disc to make it usable 
again. This is equivalent to formatting a disk on a 
computer to prepare it for use. This operation 
destroys all data on the disc.
1
With the disc loaded, and the unit in stop 
mode, press the 
ERASE
 key (
F
 or 
C
).
2
Turn the 
MULTI DIAL
 control 
B
 or use the 
 
SKIP
 keys 
H
 until the display shows 
DISC 
REFRESH
.
3
If you do not want to proceed with the refresh 
operation, press any other key (such as the 
STOP
 key).
4
To refresh the disc, press the 
MULTI DIAL
 con-
trol or press the 
ENTER
 key 
7
.
NOTE
This operation cannot be undone. If you are going to 
refresh a disc, make sure that it contains only record-
ings that you really want to erase!
5
If the refresh operation has been selected, the 
words 
ERASE XX:XX
 are shown on the 
display, and the timer starts counting down 
(
XX:XX
). The refresh operation typically 
takes around 20 minutes.
6
At the end of the countdown period, the word 
Complete
 appears briefly on the display, 
and the display returns to the track/time 
display (of course, there are no tracks, and the 
disc is as the start, with the total time of the 
disc available for recording).