Overland Storage SAN S2000 ユーザーズマニュアル
10400276-003 06/2010
©2010 Overland Storage, Inc.
Page 1 of 6
SnapServer
®
SAN S2000
Quick Start Guide
Overview
This document describes how to unpack an SnapServer
SAN S2000 appliance from Overland Storage and install
it into a four-post, 32-inch depth, EIA-310 rack.
SAN S2000 appliance from Overland Storage and install
it into a four-post, 32-inch depth, EIA-310 rack.
WARNING: To reduce the risk of electric shock or damage
to equipment, always remove any power cords while
to equipment, always remove any power cords while
working with the unit.
AVERTISSEMENT: pour réduire le risque de choc
électrique ou endommagement de l'équipement, retirez
électrique ou endommagement de l'équipement, retirez
toujours les cordons électriques en travaillant avec l'appareil.
CAUTION:
While working with the unit, observe standard
Electrostatic Discharge (ESD) precautions to prevent
damage to micro-circuitry or static-sensitive devices.
Register First
Before starting, it is essential that you activate your
Overland warranty. Technical and warranty support are
not available until this is done:
1. Go to the Overland Storage web site
Overland warranty. Technical and warranty support are
not available until this is done:
1. Go to the Overland Storage web site
(http://www.overlandstorage.com/).
, enter your e-mail address and
password (
NOTE: If you are not yet a member, click “New member?”
and follow the instructions given. It’s free and easy!
and follow the instructions given. It’s free and easy!
Figure 1. Support Site Login
5. Fill in the information and click Submit.
Within three business days, you will receive an e-mail
from Overland with your warranty certificate. Follow the
instructions included to complete the process.
Within three business days, you will receive an e-mail
from Overland with your warranty certificate. Follow the
instructions included to complete the process.
Rack Installation
Before installing the disk drives, it is recommended that
the unit first be secured in the rack.
the unit first be secured in the rack.
WARNING: Use care during rack installation or removal to
prevent accidental tipping of the rack causing damage or
prevent accidental tipping of the rack causing damage or
personal injury.
AVERTISSEMENT: soyez prudent lors de l'installation ou
de l'enlèvement du support afin d'empêcher le
de l'enlèvement du support afin d'empêcher le
renversement accidentel de la crémaillère, pour éviter
dommages et blessures.
dommages et blessures.
The rail kit included with the S2000 is adaptable for
installation in the two major types of hardware racks:
squared-holed and round-holed EIA-310 racks.
installation in the two major types of hardware racks:
squared-holed and round-holed EIA-310 racks.
NOTE: A two-post telco-style rack or any rack that is less than
29-inches in depth will not support this appliance. Also, for
threaded-hole racks, Overland Storage recommends using a
shelf.
29-inches in depth will not support this appliance. Also, for
threaded-hole racks, Overland Storage recommends using a
shelf.
The rails are not universal. They are stamped LH (left)
and RH (right) and must be mounted on the appropriate
side (when facing the rack front).
and RH (right) and must be mounted on the appropriate
side (when facing the rack front).
Attach Inner Rails to Chassis
This procedure is required for all rack types:
1. Mark the screw holes on the rack where the rails will
1. Mark the screw holes on the rack where the rails will
be installed.
NOTE: Be sure rear holes are horizontally in line with the
front holes to ensure the unit remains level.
front holes to ensure the unit remains level.
2. Remove the inner rail (
) from the rail set:
Figure 2. Inner Rail Release Latch
a. Fully extend the rail set.
b. Push the inner member latch down, and remove
b. Push the inner member latch down, and remove
the inner rail.
Inner Member Latch
Middle Member Latch
(Hidden)
Middle Member
Outer Member
*1
04002
76
00
3*