Kolpak Recording Equipment DA-98 ユーザーズマニュアル
Section 10 – Operations related to timecode
10-12 – 1.00 – 06/97
internal timecode will be captured and stored as
the timecode offset (either a positive or negative
value).
the timecode offset (either a positive or negative
value).
Note that if the words
AUTO OFFSET
are not
displayed on the screen, you cannot capture the
offset value.
offset value.
Once the offset value has been captured success-
fully, the display will change to show the captured
offset value on the bottom line.
fully, the display will change to show the captured
offset value on the bottom line.
After the timecode offset has been entered in this
way, you can “fine-tune” the value to subframe
accuracy using the method described above.
way, you can “fine-tune” the value to subframe
accuracy using the method described above.
10.7.6 Park position
When the DA-98 is slaved to an external timecode
source, it will take some time between the master
unit starting to play and starting to transmit time-
code for the DA-98 to read.
source, it will take some time between the master
unit starting to play and starting to transmit time-
code for the DA-98 to read.
These functions allow you to measure and test the
optimum pre-roll position for the DA-98 (when it
is a timecode slave) to park itself relative to the
master timecode device so that it will lock up and
start playing quickly.
optimum pre-roll position for the DA-98 (when it
is a timecode slave) to park itself relative to the
master timecode device so that it will lock up and
start playing quickly.
1) Go to menu group 4, move the cursor to
Park Posi
(park position) and press
ENTER
:
2) The time value shows the current park setting,
and this can be changed using the
UP
and
DOWN
keys, or the function keys.
10.7.7 Automatic park position setting
When the DA-98 is acting as a timecode slave, it
can automatically determine the optimum park
pre-roll position to sync with the master.
can automatically determine the optimum park
pre-roll position to sync with the master.
1) Go to menu group 4, move the cursor to
Park Posi
(park position) and press
ENTER
:
2) Play and stop the master tape.
3) Turn the DA-98’s
CHASE
on, if it is off.
4) Use the
UP
or
DOWN
keys to turn the
TEST
parameter on.
The DA-98 will then rewind so that the relative
difference is zero. When the DA-98 has stopped,
go on to the next step below.
difference is zero. When the DA-98 has stopped,
go on to the next step below.
5) Play the timecode master.
When the value shown on screen has stopped
changing and is stabilized, go on to the next step
below.
changing and is stabilized, go on to the next step
below.
6) Turn
TEST
off (
UP
or
DOWN
key). The
optimum park pre-roll time for the timecode
master is now stored.
master is now stored.
10.7.8 Absolute and relative difference
The offset as set above (10.7.2, “Setting timecode
offset”) can be called the “absolute difference”
between the two times. However, if the slave
machine “wanders” (actually, this is unlikely), the
offset (theoretical difference) will not be equal to
the absolute difference. The “relative difference”
is expressed as below:
offset”) can be called the “absolute difference”
between the two times. However, if the slave
machine “wanders” (actually, this is unlikely), the
offset (theoretical difference) will not be equal to
the absolute difference. The “relative difference”
is expressed as below:
Relative difference = Absolute difference – Offset
Thus, if the offset is set on a slave machine to
+00:10:00:00 (10 minutes) and while chasing, the
two machines’ counters read as follows:
+00:10:00:00 (10 minutes) and while chasing, the
two machines’ counters read as follows:
P a r k
P o s i t i o n
T E S T
o f f
0 2 s 0 8 f
2 5 F
P a r k
P o s i t i o n
T E S T
o f f
0 2 s 0 8 f
2 5 F
Master
10:15:12:12
Slave
10:05:12:08