Magnavox Rear-projection HDTV Monitor クイック設定ガイド
U
SING THE
TV B
UTTONS
S
hould your remote control be lost or broken, you can still
change some of the basic picture and sound settings with the
change some of the basic picture and sound settings with the
buttons on the TV. Follow the steps below to familiarize yourself
with the functions of the TV buttons.
with the functions of the TV buttons.
1
Press POWER/STANDBY
to turn the TV on (or off).
Allow about 10 seconds for the TV to power on.
2
Press the VOLUME + or – buttons
to decrease or
increase the sound level.
Press the VOLUME + and – buttons simultaneously to dis-
play the onscreen menu. After the menu appears, use these
buttons to enter submenus and make selections or adjust-
ments. (Use the CHANNEL buttons to move up and down
in the menu or submenus.) Press both VOLUME buttons
simultaneously to back out of the onscreen menus.
play the onscreen menu. After the menu appears, use these
buttons to enter submenus and make selections or adjust-
ments. (Use the CHANNEL buttons to move up and down
in the menu or submenus.) Press both VOLUME buttons
simultaneously to back out of the onscreen menus.
3
Press SOURCE SELECT
to choose from among the sig-
nal inputs you have connected to the TV.
4
Press the CHANNEL buttons
to select TV channels.
O
PERATING THE
T
ELEVISION AND
R
EMOTE
C
ONTROL
T
ELEVISION
R
EMOTE
C
ONTROL
H
OOKING UP THE
TV
I
NSTALLING
B
ATTERIES
T
o load batteries into the remote, follow these steps.
1
Gently press the tab on the battery cover
on the back of
the remote and lift the battery cover off the remote.
2
Place the two “AA” size batteries in the remote’s bat-
tery case
tery case
. Ensure that the (+) and (–) ends of the batteries
line up correctly with the (+) and (–) inside the case.
3
Press the battery cover back into place
.
P
OINTING THE
R
EMOTE
When operating the remote control, point the remote toward
the remote sensor window on the TV.
the remote sensor window on the TV.
To prevent battery leakage that may
result in injury to you or damage to the
remote control:
• Install ALL batteries correctly, + and –,
result in injury to you or damage to the
remote control:
• Install ALL batteries correctly, + and –,
as marked on the unit.
• Do not mix batteries (OLD and NEW or
CARBON and ALKALINE, etc.)
• Remove batteries when the remote con-
trol is not used for a long time.
Do not take apart, heat, or put batteries
in fire.
in fire.
Remote Sensor
Window
2
B
ATTERY
U
SAGE
CAUTION
• Be sure to point the remote toward the
sensor window on the TV.
• Be within about 30 feet (10 meters) of
the TV.
• Avoid dropping the remote on hard sur-
faces.
• Do not use harsh chemicals to clean the
remote. Use only a soft, lightly mois-
tened cloth.
tened cloth.
H
ELPFUL
H
INTS
SOURCE
SELECT
>
?
+
A
-
A
VOLUME
CHANNEL
MENU
SOURCE
SELECT
>
?
+
A
-
A
VOLUME
CHANNEL
MENU
Power Standby
Button
You can press any of the buttons on
the front of the TV to turn the TV on,
but you must press the
Power/Standby button to turn the set
off.
the front of the TV to turn the TV on,
but you must press the
Power/Standby button to turn the set
off.
H
ELPFUL
H
INT
VIDEO
S-VIDEO
L
Pb
Pr
VIDEO
S-VIDEO
L
AUDIO
L
R
AUDIO
L
R
G/Y
R/Pr
B/Pb
V
H
SYNC
L
R
AUDIO
HD INPUT-AV 4
INPUT-AV 2
OUTPUT
INPUT-AV 1
ANTENNA IN 75Ω
Y
Rear of TV
L
R
AUDIO
HD INPUT-AV 5
DVI
1
Back of TV
Antenna Signal
A
NTENNA
TV
T
his connection WILL supply stereo sound to the TV.
1
Connect the antenna signal
to the ANTENNA IN 75Ω jack
on the back of the TV.
NOTE:
Refer to the sections on TUNER MODE and AUTO
PROGRAM on page 4 of this guide. Set TUNER MODE to
the ANTENNA option. Run AUTO PROGRAM to store all
available cable channels in the TV’s memory.
the ANTENNA option. Run AUTO PROGRAM to store all
available cable channels in the TV’s memory.
MA
GNA
VO
X