LEESON Electric Saw SM Series プリント
Variable Speed AC Motor Drives
SM Series
Quick Reference Guide
7KLVJXLGHLVLQWHQGHGDVDQDLGWRFRQILJXUHWKH606HULHVGULYH
NOTE:
%HIRUHLQVWDOOLQJDQGRSHUDWLQJWKH60GULYHSOHDVH
UHDG DQG EHFRPH IDPLOLDU ZLWK WKH 60 6HULHV LQVWDOODWLRQ
DQGRSHUDWLRQPDQXDO
6KRZQEHORZDUHWZRVDPSOHZLULQJGLDJUDPVLQFOXGLQJ
IRUZDUGUHYHUVHGLUHFWLRQFRQWURO2QHVKRZVDWKUHHZLUH
VWDUWVWRSFRQWUROXVLQJPRPHQWDU\FRQWDFWVDQGWKHRWKHUVKRZVD
ZLUHVWDUWVWRSFRQWUROXVLQJPDLQWDLQHGFRQWDFWV5HTXLUHG
SDUDPHWHUVHWWLQJVDUHDOVRLQFOXGHG
:,5(67$576723
6HW3DUDPHWHU 7%$
6HW3DUDPHWHU 7%$
WR6WDUW5HYHUVH
6HW3DUDPHWHU 7%(
WR6WDUW)RUZDUG
6HW3DUDPHWHU 5RWDWLRQ
WR)RUZDUGDQG5HYHUVH
SM TERMINAL STRIP
DIAGNOSTIC AND DISPLAY MESSAGES
BULLETIN #2454
3577S/1000/6-02/RL/BH
STOP
SIGNAL COMMON
0-10 VDC SPEED REFERENCE INPUT
SPEED POT POWER SUPPLY
DIGITAL INPUT REFERENCE
TB-13A FUNCTION SELECT
TB-13B FUNCTION SELECT
TB-13E FUNCTION SELECT
4-20 mA SPEED REFERENCE INPUT
DISPLAY
DESCRIPTION
Speed Reference Codes
CP
CONTROL PAD: The drive speed is controlled by the and
buttons on the front of the drive.
EI
EXTERNAL CURRENT: The drive speed is controlled by a 4-20 mA signal between TB-25 and TB-2
EU
EXTERNAL VOLTAGE: The drive speed is controlled by a 0-10 VDC signal between TB-5 and TB-2.
JG
JOG: The drive is in Jog mode and the speed is set by preset speed #2 (Parameter 32).
OP
MOP: Contacts wired to TB-13B and 13C are used to increase and decrease the drive speed.
Pr1-Pr7
PRESET SPEEDS #1-7: The drive speed is set by the selected Preset Speed (Parameters 31-37).
Status Indication
br
DC BRAKING: The DC braking circuit is activated.
CL
CURRENT LIMIT: The output current has exceeded the CURRENT LIMIT setting (Parameter 25)
and the drive is reducing the output frequency to reduce the output current. If the drive
remains in CURRENT LIMIT for too long, it can trip into a CURRENT OVERLOAD fault (PF).
and the drive is reducing the output frequency to reduce the output current. If the drive
remains in CURRENT LIMIT for too long, it can trip into a CURRENT OVERLOAD fault (PF).
Er
ERROR: Invalid data has been entered.
GE
“GE” will be displayed if an attempt is made to change the OEM default settings when the
drive is operating in the OEM mode (see Parameter 48).
drive is operating in the OEM mode (see Parameter 48).
LC
FAULT LOCKOUT: Failed three restart attempts. Requires a manual reset.
SE
SERIAL: The optional remote keypad is active as the user interface instead of the buttons on the
front of the drive.
front of the drive.
SP
START PENDING: This is displayed during the 15 second interval between restart attempts.
Diagnostic Codes
AF
HIGH TEMPERATURE FAULT: Ambient temperature is too high.
CF
CONTROL FAULT: A blank EPM, or EPM with corrupted data has been installed. Perform a
factory reset (Parameter 48).
factory reset (Parameter 48).
cF
INCOMPATIBILITY FAULT: An EPM with a different parameter version has been installed.
dF
DYNAMIC BRAKING FAULT: The drive has sensed the dynamic braking resistors are overheating.
EF
EXTERNAL FAULT: TB-13A and/or TB13C is set as an external fault input and TB-13A and/or
TB-13C is open with respect to TB-2.
TB-13C is open with respect to TB-2.
GF
DATA FAULT: User data and OEM defaults in the EPM are corrupted.
HF
HIGH DC BUS VOLTAGE FAULT: Line voltage is too high; Deceleration rate is too fast;
Overhauling load. Fast deceleration and overhauling loads may require dynamic braking.
Overhauling load. Fast deceleration and overhauling loads may require dynamic braking.
JF
REMOTE KEYPAD FAULT: The communication link between the drive and the optional Remote
Keypad has been lost. Check for proper wiring and/or noise.
Keypad has been lost. Check for proper wiring and/or noise.
LF
LOW DC BUS VOLTAGE FAULT: Line voltage is too low.
OF
OUTPUT TRANSISTOR FAULT: Phase to phase or phase to ground short circuit on the
output: Failed output transistor: Boost settings are too high: Acceleration rate is too fast.
output: Failed output transistor: Boost settings are too high: Acceleration rate is too fast.
PF
CURRENT OVERLOAD FAULT: VFD is undersized for the application: Mechanical problem with
the driven equipment.
the driven equipment.
SF
SINGLE-PHASE FAULT: Single-phase input power has been applied to a three-phase drive.
UF
START FAULT: Start command was present when the drive was powered up. Must wait
2 seconds after power-up to apply Start command if START METHOD is set to NORMAL.
2 seconds after power-up to apply Start command if START METHOD is set to NORMAL.
F1
EPM FAULT: The EPM is missing or damaged.
FC,F2-Fo
INTERNAL FAULTS: The control board has sensed a problem. Consult factory.
:,5(67$576723
6HW3DUDPHWHU 7%$
6HW3DUDPHWHU 7%$
WR5XQ5HYHUVH
6HW3DUDPHWHU 5RWDWLRQ
WR)RUZDUGDQG5HYHUVH
1
2
5
6
11
13A
13B
13E
25
16
17
PROGRAMMABLE FORM A RELAY
1
2
5
6
11 13A 13B 13E 25
Momentary
Momentary
Stop Contact
Start Contact
1
2
5
6
11 13A 13B 13E 25
Maintained
Maintained
Run Forward
Run Reverse
Contact
Contact
REV
FWD
A Subsidiary of REGAL-BELOIT CORPORATION