Enterasys Networks MATRIX 7H4385-49 ユーザーズマニュアル
Preparing to Install into a Matrix E7, N1, N3, N5, or N7 Chassis
3-8 Installation
5.
Examine the module for damage. If any damage exists, DO NOT install the module.
Immediately contact Enterasys Networks. Refer to “
Immediately contact Enterasys Networks. Refer to “
6.
To install a 7H4385‐49 into a Matrix E7 or
Matrix N7, proceed to “
” on page 3‐8. For Matrix N1,
Matrix N3, or Matrix N1, refer to “
Installing the 7H4385-49
into a Matrix E7 or Matrix N7 Chassis
and proceed as follows:
1.
Prepare the chassis as described in “
2.
Locate the chassis card guides that line up with the slot number in which the module
will be installed. Make sure the module locking levers are in the open position (top
and bottom).
will be installed. Make sure the module locking levers are in the open position (top
and bottom).
Caution: To prevent damaging the backplane connectors in the following step, take care
that the module slides in straight and properly engages the backplane connectors.
that the module slides in straight and properly engages the backplane connectors.
Ensure that the top lever lines up with the desired slot number located on the front panel
of the chassis. Refer to
of the chassis. Refer to
Precaución: Para evitar que se dañen los conectores del panel posterior en el siguiente
paso, intente deslizar el módulo en forma recta y verifique que se enganche
correctamente en los conectores de panel posterior.
Asegúrese de que la palanca superior esté alineada con respecto al número de ranura
correspondiente ubicado en el panel frontal del chasis. Consulte en
paso, intente deslizar el módulo en forma recta y verifique que se enganche
correctamente en los conectores de panel posterior.
Asegúrese de que la palanca superior esté alineada con respecto al número de ranura
correspondiente ubicado en el panel frontal del chasis. Consulte en
Electrical Hazard: To prevent exposure to an energy hazard in a 7H4385-49 connected
to an external N-POE Power System, disconnect the 48-Vdc power cable from the 48-Vdc
input connector before servicing or removing the 7H4385-49.
to an external N-POE Power System, disconnect the 48-Vdc power cable from the 48-Vdc
input connector before servicing or removing the 7H4385-49.
Riesgo Eléctrico: Para prevenir la exposicion a un riesgo electrico en una tarjeta
7H4385-49 conectada a un sistema externo de energia N-POE Power System,
desconectar el cable de poder de 48-Vdc del conector de entrada 48-Vdc antes de dar
servicio o remover la tarjeta 7H4385-49.
7H4385-49 conectada a un sistema externo de energia N-POE Power System,
desconectar el cable de poder de 48-Vdc del conector de entrada 48-Vdc antes de dar
servicio o remover la tarjeta 7H4385-49.
Elektrischer Gefahrenhinweis: Um den Schutz vor el. Schäden des Moduls
(7H4385-49) zu gewähleisten, bei Verwendung der N-POE Systeme, sollte dies bevor
man dieses entnimmt oder Servicearbeiten daran vornimmt, vom 48-Vdc Stecker getrennt
werden.
(7H4385-49) zu gewähleisten, bei Verwendung der N-POE Systeme, sollte dies bevor
man dieses entnimmt oder Servicearbeiten daran vornimmt, vom 48-Vdc Stecker getrennt
werden.