FMC Corporation - Talstar FMC L06 ユーザーズマニュアル
Doc No: OMM50000903
Rev: B Page 59 of 65
Subject to contractual terms and conditions to the contrary, this document and all the information contained herein are the confidential and exclusive
property of FMC Technologies, and may not be reproduced, disclosed, or made public in any manner prior to express written authorization by FMC.
Pump runs
rough,
knocks, or
vibrates
(ONLY)
rough,
knocks, or
vibrates
(ONLY)
-Broken or weak valve spring
-Valve damaged or unseated
-Loose plunger, piston, or rod
-Low oil level in power end
-Excessive connecting rod bearing
clearance
-Excessive main bearing clearance
-Worn wrist pin or bearing
-Pump running backward
-Loose sheaves or bushings (v-belt drive)
-Gear tooth cracked or broken
-Insufficient NPSHA
-Excessive acceleration head in suction line
-Pulsation dampener improperly charged
-Inlet line too long or too small in diameter
-Worn piston seal allows air ingress
(usually observed when booster not used)
-Valve damaged or unseated
-Loose plunger, piston, or rod
-Low oil level in power end
-Excessive connecting rod bearing
clearance
-Excessive main bearing clearance
-Worn wrist pin or bearing
-Pump running backward
-Loose sheaves or bushings (v-belt drive)
-Gear tooth cracked or broken
-Insufficient NPSHA
-Excessive acceleration head in suction line
-Pulsation dampener improperly charged
-Inlet line too long or too small in diameter
-Worn piston seal allows air ingress
(usually observed when booster not used)
-Replace valve spring
-Repair/replace valve or re-seat
-Tighten loose components
-Fill to proper level
-Check cap torque or replace bearings
-Adjust end-play
-Replace worn components
-Correct rotation
-Tighten loose components
-Replace gear
-Provide more NPSH
-Install suction stabilizer
-Charge to proper pressure
-Increase suction pipe size
-Replace piston seal
-Repair/replace valve or re-seat
-Tighten loose components
-Fill to proper level
-Check cap torque or replace bearings
-Adjust end-play
-Replace worn components
-Correct rotation
-Tighten loose components
-Replace gear
-Provide more NPSH
-Install suction stabilizer
-Charge to proper pressure
-Increase suction pipe size
-Replace piston seal
Rapid suction
pressure
fluctuation
pressure
fluctuation
-Pump cavitation
-Air is entering suction line
-Air is entering suction line
-Increase suction size or NPSH
-Correct installation to stop leaks
-Correct installation to stop leaks
Piping
vibration
vibration
-Same as Pump runs rough above
-Excessive pressure variation in discharge
-Piping inadequately supported
-Excessive short-radius elbows or tees
-Excessive pressure variation in discharge
-Piping inadequately supported
-Excessive short-radius elbows or tees
-See above
-Install discharge pulsation dampener
-Install supports at proper locations
-Correct installation to minimize turns and
short-radius fittings
-Install discharge pulsation dampener
-Install supports at proper locations
-Correct installation to minimize turns and
short-radius fittings
Pump
requires
excessive
power
requires
excessive
power
-Discharge pressure too high
-Plungers or pistons too large
-Speed too high
-Packing too tight
-Misaligned coupling
-Belts too tight
-Power end bearings too tight
-Low motor voltage
-Plungers or pistons too large
-Speed too high
-Packing too tight
-Misaligned coupling
-Belts too tight
-Power end bearings too tight
-Low motor voltage
-Reduce system back-pressure or relief valve
-Install smaller plungers to reduce flow
-Reduce speed
-Loosen gland (Adjustable packing)
-Correct alignment
-Correctly adjust belt tension
-Increase end-play
-Supply correct voltage
-Install smaller plungers to reduce flow
-Reduce speed
-Loosen gland (Adjustable packing)
-Correct alignment
-Correctly adjust belt tension
-Increase end-play
-Supply correct voltage
Power end
overheats
(over 180° F)
and/or
reduced
power
component
end life
overheats
(over 180° F)
and/or
reduced
power
component
end life
-Discharge and/or suction pressure too high
-Oil level too high or too low
-Contaminated power end oil
-Incorrect oil viscosity or grade
-Misaligned coupling
-Belts too tight
-Pump running backward
-Pump located too close to heat source
-Worn or damaged power end bearings
-Oil level too high or too low
-Contaminated power end oil
-Incorrect oil viscosity or grade
-Misaligned coupling
-Belts too tight
-Pump running backward
-Pump located too close to heat source
-Worn or damaged power end bearings
-Reduce pressure or reduce plunger size
-Adjust to correct oil level
-Refill with clean oil & eliminate contamination
-Fill with correct oil
-Correct alignment
-Correctly adjust belt tension
-Correct rotation
-Remove heat source or insulate power end
-Replace damaged bearings
-Adjust to correct oil level
-Refill with clean oil & eliminate contamination
-Fill with correct oil
-Correct alignment
-Correctly adjust belt tension
-Correct rotation
-Remove heat source or insulate power end
-Replace damaged bearings
Crankshaft
jerks or starts
and stops
rotation
jerks or starts
and stops
rotation
-Drive belts loose and slipping (if equipped)
-System relief valve pressure set too high
-Discharge line blocked or partially blocked
-System relief valve pressure set too high
-Discharge line blocked or partially blocked
-Correctly adjust belt tension
-Reduce relief valve pressure setting
-Clear obstructions from piping system
-Reduce relief valve pressure setting
-Clear obstructions from piping system