Garmin Vector S オーナーマニュアル
2
Plug the small end of the USB cable into the USB port on the
device.
3
Plug the large end of the USB cable into a computer USB
port.
4
Go to
.
5
Follow the on-screen instructions.
Garmin Connect
You can connect with your friends on Garmin Connect. Garmin
Connect gives you the tools to track, analyze, share, and
encourage each other. Record the events of your active lifestyle
including runs, walks, rides, swims, hikes, triathlons, and more.
.
Store your activities: After you complete and save an activity
with your device, you can upload that activity to Garmin
Connect and keep it as long as you want.
Analyze your data: You can view more detailed information
about your activity, including time, distance, elevation, heart
rate, calories burned, cadence, an overhead map view, pace
and speed charts, and customizable reports.
NOTE: Some data requires an optional accessory such as a
NOTE: Some data requires an optional accessory such as a
heart rate monitor.
Plan your training: You can choose a fitness goal and load one
of the day-by-day training plans.
Share your activities: You can connect with friends to follow
each other's activities or post links to your activities on your
favorite social networking sites.
Disconnecting the USB Cable
If your device is connected to your computer as a removable
drive or volume, you must safely disconnect your device from
your computer to avoid data loss. If your device is connected to
your Windows
®
computer as a portable device, it is not
necessary to safely disconnect.
1
Complete an action:
• For Windows computers, select the Safely Remove
• For Windows computers, select the Safely Remove
Hardware icon in the system tray, and select your device.
• For Mac
®
computers, drag the volume icon to the trash.
2
Disconnect the cable from your computer.
Device Information
Vector Device Care
NOTICE
Keep the components clean and free of debris.
Do not use a sharp object to clean the device.
Avoid chemical cleaners, solvents, and insect repellents that can
Do not use a sharp object to clean the device.
Avoid chemical cleaners, solvents, and insect repellents that can
damage plastic components and finishes.
Do not submerge or pressure wash the components.
Do not store the device where prolonged exposure to extreme
Do not submerge or pressure wash the components.
Do not store the device where prolonged exposure to extreme
temperatures can occur, because it can cause permanent
damage.
Replace components with Garmin parts only. See your Garmin
Replace components with Garmin parts only. See your Garmin
dealer or the Garmin website.
Removing the Pedal Pods and Pedals
NOTICE
Do not attempt to pry the cable from the spindle.
NOTE: This task is for the Vector 2 system.
1
Use the 2.5 mm hex key to remove the screw from the pedal
pod.
2
Use the pedal wrench
À
to slowly loosen the pedal
Á
.
NOTE: The spindle and crank for the left pedal has a left-
handed (reverse) thread.
As you unscrew the pedal, the pedal pod cable disengages
As you unscrew the pedal, the pedal pod cable disengages
from the spindle.
NOTE: When you install Vector again, you must recalibrate
NOTE: When you install Vector again, you must recalibrate
the system.
Replacing the Pedals and Cartridges
NOTICE
You must obtain a cartridge axle tool (available from Exustar
™
or
Shimano
®
), 8 mm hex nut driver, 15 mm pedal wrench, and bike
grease. Other compatible tools can be used. Use care not to
damage any of the Vector components.
If your pedals are damaged or show significant wear, you can
replace the pedals, cartridges, and related hardware
components.
NOTE: Pedal and cartridge replacement is the same for the
NOTE: Pedal and cartridge replacement is the same for the
Vector and Vector S systems. You should keep the left pedal
parts separate from the right pedal parts.
1
Remove the pedals and pedal pods from your bike
).
2
Use the cartridge axle tool to unscrew the pedal body from
the cartridge
À
.
4
Device Information