BMW 2008 M3 Sedan オーナーマニュアル
Under t
h
e
ho
od
110
M dual clutch transmission: the oil level
appears in the top display.
appears in the top display.
<
The oil level must be between the two mark-
ings.
A new measurement is taken automatically
each time the engine is started.
ings.
A new measurement is taken automatically
each time the engine is started.
Possible displays
1 Oil level OK.
2 Oil level is being checked.
2 Oil level is being checked.
This can take about 1 minute if the car is at
a standstill on a level surface, or about
5 minutes while the car is moving.
If engine oil was added, it can take up to
30 minutes to get an oil level reading.
a standstill on a level surface, or about
5 minutes while the car is moving.
If engine oil was added, it can take up to
30 minutes to get an oil level reading.
3 Oil level down to minimum:
Add engine oil at the next opportunity, but
no more than 1 US quart/1 liter, refer also to
Adding engine oil on page
no more than 1 US quart/1 liter, refer also to
Adding engine oil on page
. Add at least
0.5 US quart/0.5 liters, otherwise the oil-
level monitor will be unable to display the
new value reliably.
If the oil level is below the minimum value,
add engine oil immediately to avoid engine
damage.
level monitor will be unable to display the
new value reliably.
If the oil level is below the minimum value,
add engine oil immediately to avoid engine
damage.
4 Oil level is too high.
Have the vehicle checked immedi-
ately, otherwise the excess oil may
ately, otherwise the excess oil may
lead to engine damage.
<
5 A value cannot be read at this time. The
engine is not yet warm.
Quick measurement
In addition to the automatic measurement, you
can also determine the current oil level manu-
ally, e.g. after adding engine oil, but such mea-
surements are less accurate.
can also determine the current oil level manu-
ally, e.g. after adding engine oil, but such mea-
surements are less accurate.
1.
Park the vehicle with a warm engine, i.e.
after an uninterrupted drive of at least
6 miles/10 km, on a horizontal surface.
after an uninterrupted drive of at least
6 miles/10 km, on a horizontal surface.
2.
Let the engine idle.
3.
Press the computer button in the turn indi-
cator lever repeatedly until the oil level dis-
play appears in the instrument cluster.
cator lever repeatedly until the oil level dis-
play appears in the instrument cluster.
4.
Press the computer button for at least
2 seconds.
The oil level is determined. A clock symbol
appears during measurement.
2 seconds.
The oil level is determined. A clock symbol
appears during measurement.
5.
After approx. 1 minute, the current oil level
is displayed.
is displayed.
Adding engine oil
Do not add 1 US quart/1 liter of engine oil until
the display shows an oil level measurement of
"+1qt" or "+1l".
the display shows an oil level measurement of
"+1qt" or "+1l".
Add oil within the next 125 miles/200 km,
otherwise the engine could be damaged.
otherwise the engine could be damaged.
Add no more than 1 US quart/1 liter of oil, oth-
erwise too much engine oil can lead to engine
damage. Add at least 0.5 US quart/0.5 liters,
otherwise the oil-level monitor will be unable to
display the new value reliably.
erwise too much engine oil can lead to engine
damage. Add at least 0.5 US quart/0.5 liters,
otherwise the oil-level monitor will be unable to
display the new value reliably.
<
Online Edition for Part no. 01 41 0 014 956 - © 02/08 BMW AG