Bosch Appliances Security Camera PT-400 ユーザーズマニュアル
Security Escort | Technical Reference Manual | 3.0 System Menus
and Screens
and Screens
EN | 44
Bosch Security Systems | 6/12 | 38947D
Spare
This is a future option. Not
implemented at this time.
Low Battery Map
Requests a map of all the alert units
that are currently reporting a Low
Battery to the system. The Low Battery
Map button displays a map with “1” in
the locations corresponding to points
that are reporting Low Battery.
I’m OK Check, I’m OK Release Control
Buttons
This is a future option. Not
implemented at this time.
Low Battery Map
Requests a map of all the alert units
that are currently reporting a Low
Battery to the system. The Low Battery
Map button displays a map with “1” in
the locations corresponding to points
that are reporting Low Battery.
I’m OK Check, I’m OK Release Control
Buttons
These buttons are used to diagnose and
correct communications problems between
the central console and the
transponder. The system software
requires that each transponder send a
message to the central console
periodically if no other communications
have taken place. These messages are
called I’m OK messages. If for some
reason the communications link between
the central console and the transponder
fails, the transponder recognizes the
fact when its I’m OK transmissions are
not acknowledged by the central
console. When the transponder has
retried transmitting an I’m OK message
or any other message six times without
acknowledgment, it assumes control of
the outputs (LED’s, horns, strobes, and
sirens) on devices connected to it and
modifies the message to indicate that
it is still OK and has taken control.
These messages are transmitted once per
minute until communications are
reestablished.
correct communications problems between
the central console and the
transponder. The system software
requires that each transponder send a
message to the central console
periodically if no other communications
have taken place. These messages are
called I’m OK messages. If for some
reason the communications link between
the central console and the transponder
fails, the transponder recognizes the
fact when its I’m OK transmissions are
not acknowledged by the central
console. When the transponder has
retried transmitting an I’m OK message
or any other message six times without
acknowledgment, it assumes control of
the outputs (LED’s, horns, strobes, and
sirens) on devices connected to it and
modifies the message to indicate that
it is still OK and has taken control.
These messages are transmitted once per
minute until communications are
reestablished.
The I’m OK Check button requests that
the transponder send an I’m OK message.
This is used to determine if a
transponder has taken control of its
outputs. The I’m OK Release Control
button generates a command to the
transponder to release control back to
the central console. Normally, the
central console automatically generates
a Release Control message upon the re-
establishment of communications
following a failure.
the transponder send an I’m OK message.
This is used to determine if a
transponder has taken control of its
outputs. The I’m OK Release Control
button generates a command to the
transponder to release control back to
the central console. Normally, the
central console automatically generates
a Release Control message upon the re-
establishment of communications
following a failure.
Out Of Service Map
The Out Of Service Map shows those
points (receivers or alert units) that
are currently out of service. Points
may be taken out of service and
returned to service by selecting the
point using MUX Bus Point Screen in the
bottom right corner of the screen and
clicking the Point Out Of Service or
Point In Service button. Points can be
selected by typing in the point number
or by using the [+] and [-] buttons, or
the [?] button.
Point Out Of Service
Clicking this button takes the
currently selected point out-of-
service. That point no longer responds
to the system, as if it was
disconnected. Use this function with
caution.
Point In Service
Clicking this button restores the
currently selected point to an in-
service condition. That point returns
to normal function.
Transponder Outputs
Requests the current state of the siren
and strobe outputs on the transponder.
Reset Transponder
Clicking this button resets the
transponder as if it was just powered
up. Any test or alarm processing that
was in progress at the time is lost.
Horn - Siren
If this checkbox is checked, the horn
output of a receiver or the siren
output of an alert unit is turned on if
On Output Command is clicked, or off if
Off is clicked. If this checkbox is not
checked, the state of this output is
not changed.
Green LED
If this checkbox is checked, the green
LED output of a receiver or the spare
output of an alert unit is turned on if
On Output Command is clicked, or off if
Off is clicked. If this checkbox is not
checked, the state of this output is
not change.
Strobe – Red LED
If this checkbox is checked, the red
LED output of a receiver or the strobe
output of an alert unit is turned on if
On Output Command is clicked, or off if
Off is clicked. If this checkbox is not
checked, the state of this output is
not changed.
The Out Of Service Map shows those
points (receivers or alert units) that
are currently out of service. Points
may be taken out of service and
returned to service by selecting the
point using MUX Bus Point Screen in the
bottom right corner of the screen and
clicking the Point Out Of Service or
Point In Service button. Points can be
selected by typing in the point number
or by using the [+] and [-] buttons, or
the [?] button.
Point Out Of Service
Clicking this button takes the
currently selected point out-of-
service. That point no longer responds
to the system, as if it was
disconnected. Use this function with
caution.
Point In Service
Clicking this button restores the
currently selected point to an in-
service condition. That point returns
to normal function.
Transponder Outputs
Requests the current state of the siren
and strobe outputs on the transponder.
Reset Transponder
Clicking this button resets the
transponder as if it was just powered
up. Any test or alarm processing that
was in progress at the time is lost.
Horn - Siren
If this checkbox is checked, the horn
output of a receiver or the siren
output of an alert unit is turned on if
On Output Command is clicked, or off if
Off is clicked. If this checkbox is not
checked, the state of this output is
not changed.
Green LED
If this checkbox is checked, the green
LED output of a receiver or the spare
output of an alert unit is turned on if
On Output Command is clicked, or off if
Off is clicked. If this checkbox is not
checked, the state of this output is
not change.
Strobe – Red LED
If this checkbox is checked, the red
LED output of a receiver or the strobe
output of an alert unit is turned on if
On Output Command is clicked, or off if
Off is clicked. If this checkbox is not
checked, the state of this output is
not changed.