Bosch 2000 ユーザーズマニュアル

2000 Series | Program Entry Guide | 3.0 

Reports 

EN | 12 

 

 

Bosch Security Systems | 7/05 | 35114F 

 

If the system is on with No Delay, alarm output at 
Terminals 4 and 5 follows the alarm delay 
programmed here. The alarm sounds at the keypad 
without delay. 

When mixing Delay Alarm points (Digit 2 set for 7 
or 8), with No Delay Alarm points (Digit 2 set for 5, 
6, or 9), the alarm output follows the programmed 
alarm delay if Delay Alarm points are faulted first. 

255 = Voice Verification:  Only set the 

Delay 

Alrm Rpt

 prompt to 255 when using an optional 

two-way voice verification module. When the 

Delay 

Alrm Rpt

 prompt is set to 255, an Alarm event on a 

point with 2, 3, 7, or 8 in Digit 2 sends an Alarm 
Report and begins the two-way voice verification 
process. Do not set the 

 Delay Alrm Rpt

 prompt to 

255 if a voice verification module is not connected to 
the control panel, because unexpected control panel 
operation results. 

 

 

Duress Reports and A, B, C Key Reports 
are affected by Alarm Report Delay. These 
reports are sent immediately in all cases. 

 

 

 

The Security Industry Association (SIA) 
recommends the Delay Alarm Report 
feature be enabled with the delay set to 15 
seconds. Enter 15 at this prompt to comply 
with the SIA recommendation. 

Press the [0] key to disable the 

Delay Alrm Rpt

 

prompt for all points. 

Default: 

Yes

 

Yes, No

 

0 No 

1 Yes 

Set the 

Cancel Rpt

 prompt to Yes to enable Cancel 

Report. If a user turns the system off after an alarm, 
but before bell time expires, a Cancel

 

Report follows 

the Alarm Report. 

If the user turns the system off before 

Delay Alrm 

Rpt

 prompt time expires, the control panel sends no 

Alarm, Cancel, or Restoral Report for points 
programmed with a 2, 3, 7, or 8 in Digit 2 of the 
point code. 

If you set the 

Cancel Rpt

 prompt to No, the control 

panel does not send Cancel Reports. 

Default: 

No

 

No, Yes, Delay

 

0 No 

1 Yes 

2 Delay 

Set the 

Restoral Rpts

 prompt to Yes to send 

Restoral Reports to the receiver for 

all points. The 

system sends Restoral Reports when points return to 
normal (not faulted) after an Alarm or Trouble 
Report. 

Set the 

Restoral Rpts

 prompt to No to prevent the 

system from sending Restoral Reports for any point. 

Set the 

Restoral Rpts

 prompt to Delay to delay 

sending Restoral Reports until bell time expires.  

Default: 

No Buzz, No Report

 

No Buzz, No Report 
Buzz, No Report 
Buzz, Report 
Buzz, Tag-Along Rpt 
No Buzz, Report 
No Buzz, Tag-Along Rpt

 

No Buzz No Report 

0 

Buzz, No Report 

1 

Buzz, Report 

2 

Buzz, Tag-Along Rpt 

3 

No Buzz Report 

4 

No Buzz, Tag-Along Rpt 

5 

The control panel monitors AC power. When AC 
power to terminals 1 and 2 is interrupted, the control 
panel waits 60 seconds. If AC power is not restored 
within 60 seconds, it provides the response 
programmed in 

AC Fail Buzz/Rpt

. 

When set to 

No Buzz, No Report the system only 

flashes the OK light at the keypad to indicate a 
system trouble. It does not sound the trouble tone or 
send a report to the receiver. 

When set to 

Buzz, No Report the system flashes the 

OK light at the keypad to indicate a system trouble 
and sounds the trouble tone. No report is sent to the 
receiver.