Bosch 2000 ユーザーズマニュアル
2000 Series | Program Entry Guide | 1.0
System Configuration
EN | 5
Bosch Security Systems | 7/05 | 35114F
1.0 System
Configuration
The System Configuration Group contains the
Account Number
,
Swinger Count
,
Keyswitch
,
Custom Idle Text
, and
Custom Service Text
prompts.
1 Account Number
Default:
0000
Selection:
0 to 9, B to F
Enter four characters for the
Account Number
to
transmit to the receiver. Enter leading zeroes (0) for
account numbers with fewer than four digits. For
example: Enter 0123 for account number 123.
account numbers with fewer than four digits. For
example: Enter 0123 for account number 123.
2 Swinger Count
Default:
4
Selection:
1, 2, 3, 4
The
Swinger Count
prompt sets the swinger count
for the Swinger Bypass point option. When the
number of alarms or troubles reaches the swinger
count, the system automatically bypasses points
programmed for Swinger Bypass. Turning the
system off clears the bypass. If a 24-hour point
swinger bypasses while the system is off, turning the
system on (starting exit delay) and then turning it off
(pressing [CLEAR] during exit delay) clears the
bypass. Swinger bypass is a point trouble and
activates the Point Trouble Relay function.
number of alarms or troubles reaches the swinger
count, the system automatically bypasses points
programmed for Swinger Bypass. Turning the
system off clears the bypass. If a 24-hour point
swinger bypasses while the system is off, turning the
system on (starting exit delay) and then turning it off
(pressing [CLEAR] during exit delay) clears the
bypass. Swinger bypass is a point trouble and
activates the Point Trouble Relay function.
When a point is Swinger Bypassed, the Point
Trouble Relay function activates. Refer to Section
13.2 Relay Functions.
Trouble Relay function activates. Refer to Section
13.2 Relay Functions.
SIA recommends the swinger count be set
to 1.
to 1.
Using Digit 2 of the point code assigns the Swinger
Bypass feature to a point.
Bypass feature to a point.
3 Keyswitch
Default:
Momentary
Selection:
Easikey, Momentary
0 Easikey
1 Momentary
Refer to the Installation Guide for instructions on
connecting a momentary keyswitch to a point.
connecting a momentary keyswitch to a point.
This control panel is not compatible with
maintained contact keyswitches.
maintained contact keyswitches.
Operating the keyswitch (shorting the point) turns
the system All On with delays if the system is off.
Any faulted controlled points (Point Code Digit 1 =
6, 7, 8, 9, B, or C) are automatically bypassed.
the system All On with delays if the system is off.
Any faulted controlled points (Point Code Digit 1 =
6, 7, 8, 9, B, or C) are automatically bypassed.
If the system is All On or Part On, with or without
delays, operating the keyswitch (shorting the point)
turns the system off.
delays, operating the keyswitch (shorting the point)
turns the system off.
Leave the
Keyswitch
prompt set to Momentary if
you are not using a keyswitch on your system.
Setting the
Keyswitch
prompt to Easikey allows a
properly connected Easikey system to disarm the
system. It cannot be used to arm the system. If the
system is All On or Part On, with or without delays,
presenting the electronic key to the Easikey reader
(the Easikey shorts the point) turns the system off. If
the system is off, presenting the electronic key to the
Easikey reader (the Easikey shorts the point) has no
effect.
system. It cannot be used to arm the system. If the
system is All On or Part On, with or without delays,
presenting the electronic key to the Easikey reader
(the Easikey shorts the point) turns the system off. If
the system is off, presenting the electronic key to the
Easikey reader (the Easikey shorts the point) has no
effect.
4 Custom Idle Text1
5 Custom Idle Text2
Default:
Bosch Security Systems
Selection:
A to Z, 0 to 9,
! # , . - / : < >
! # , . - / : < >
The system displays at all text keypads the two lines
of custom text you enter here whenever the system
is off and idle. Each line contains a maximum of
sixteen characters.
of custom text you enter here whenever the system
is off and idle. Each line contains a maximum of
sixteen characters.
It can take up to 15 seconds for the
custom text you program here to appear in
all text keypads connected to the system.
custom text you program here to appear in
all text keypads connected to the system.