White Rodgers 25M01A-100 25M Gas Dryer Valves インストール手順
2
CAUTION
!
WARNING
!
If you do not follow these instructions exactly, a fire or explosion may
result, causing property damage, personal injury or loss of life.
result, causing property damage, personal injury or loss of life.
DO NOT BEGIN INSTALLATION UNTIL YOU READ THE
FOLLOWING PRECAUTIONS.
FOLLOWING PRECAUTIONS.
PRECAUTIONS
1. Failure to turn off electric or main gas supply to
clothes dryer could cause personal injury and/or
property damage by shock, gas suffocation, fire,
and/or explosion.
property damage by shock, gas suffocation, fire,
and/or explosion.
2. Do not use this control on circuits exceeding speci-
fied voltage. Higher voltage will damage the control
and may cause shock or fire hazard.
and may cause shock or fire hazard.
3. NEVER USE FLAME OR ANY KIND OF SPARK TO
CHECK FOR GAS LEAKS–COULD CAUSE FIRE
AND/OR EXPLOSION.
AND/OR EXPLOSION.
4. Do not use a control set for natural gas with LP gas,
or a control set for LP gas with natural gas. Personal
injury and/or property damage, gas suffocation, fire,
and/or explosion may result.
injury and/or property damage, gas suffocation, fire,
and/or explosion may result.
1. Do not short out terminals on gas valve or primary
control to test. Short or incorrect wiring can cause
equipment damage, property damage, and/or per-
sonal injury.
equipment damage, property damage, and/or per-
sonal injury.
2. This control is not intended for use in locations
where it may come in direct contact with water.
Suitable protection must be provided to shield the
control from exposure to water (dripping, spraying,
rain, etc.).
Suitable protection must be provided to shield the
control from exposure to water (dripping, spraying,
rain, etc.).
INSTALLATION
1. Before attempting to service dryer, unplug power cord,
turn off main gas supply and consult dryer manufacturer's
instructions for accessing gas valve.
instructions for accessing gas valve.
2. Disconnect exhaust vent duct.
3. Disconnect gas line from rear of dryer.
4. Remove access panel from dryer. On some models this
3. Disconnect gas line from rear of dryer.
4. Remove access panel from dryer. On some models this
involves removing the entire front panel.
5. The gas valve/burner assembly should now be visible.
6. The burner assembly consists of (see figure 1 & 2):
6. The burner assembly consists of (see figure 1 & 2):
a. Gas inlet pipe.
b. Brass inlet fitting with union – some models may also
b. Brass inlet fitting with union – some models may also
have a manual shut-off valve.
c. Gas valve.
d. Mounting bracket.
e. Burner orifice.
f. Burner assembly with air shutter.
g. Igniter.
h. Radiant sensor – located on heat exchanger on
d. Mounting bracket.
e. Burner orifice.
f. Burner assembly with air shutter.
g. Igniter.
h. Radiant sensor – located on heat exchanger on
some models.
7. Disconnect the wiring harness from gas valve and igniter.
8. Remove screw(s) fastening the mounting bracket to the
8. Remove screw(s) fastening the mounting bracket to the
bottom of dryer.
9. Burner assembly should now be free to slide out of the
front of dryer. Take care not to bump or jar igniter. It is
very fragile.
10. Remove the gas inlet pipe by unscrewing the union.
11. Remove screw(s) fastening the gas valve to the mounting
11. Remove screw(s) fastening the gas valve to the mounting
bracket and set them aside. They will be reused.
12. The gas valve should now be free to slide out of burner
and off of mounting bracket. Take care not to disturb the
air shutter.
Figure 1
G
H
F
E (not shown)
C
B
C
E
D
B
A
Figure 2
G
H
F
E (not shown)
C
B
C
E
D
B
A