Whirlpool SF315PEPB0 ユーザーズマニュアル

■

Is the power outlet properly wired and polarized? Try 
another outlet to check for proper wiring and polarity.

■

Is the power supply cord unplugged? Plug into a properly 
grounded 3 prong outlet.

■

Has a household fuse been blown or has the circuit 
breaker tripped? Replace the fuse or reset the circuit.

■

Is the main or regulator gas shutoff valve in the off 
position? See Installation Instructions.

■

Is the range properly connected to the gas supply? 
Contact a trained repair specialist or see Installation 
Instructions.

■

Is this the first time the surface burners have been used?    
Turn on any one of the surface burner knobs to release air 
from the gas lines.

■

Is the control knob set correctly? Push in knob before 
turning to a setting.

■

Are the burner ports clogged? On sealed burner models, 
see “Sealed Surface Burners” section. On open burner 
models, see “Surface Burners” section.

■

Are the burner ports clogged?  On sealed burner models, 
see “Sealed Surface Burners” section. On open burner 
models, see “Surface Burners” section.

■

On models with caps, are the burner caps positioned 
properly? See “Sealed Surface Burners” section.

■

Is the burner damaged? On models with caps, look for 
warped cap. Place cap, flat sidedown, on a flat surface. If cap 
wobbles noticeably, it is warped. Place cap on different 
burner for further check of warping. Replace warped cap. 
Contact a trained repair specialist if the condition does not 
improve.

■

Is the air/gas mixture correct? Contact a designated 
service technician to check the air/gas mixture, or see the 
Installation Instructions.

■

Is propane gas being used? The appliance may have been 
converted improperly.    Contact a trained repair specialist.

■

Is the burner wet? Let it dry.

■

Is the range level? Level the range. (See the Installation 
Instructions.)

■

Is the proper cookware being used? Use cookware with a 
flat bottom. (See “Cookware” section.)

■

Is the cookware the proper size? Use cookware about the 
same size as the surface cooking area, element or surface 
burner. Cookware should not extend more than 1" (2.5 cm) 
outside the cooking area.

■

Are the right side surface burners rotated toward each 
other? See “Burner Rotation” section.

■

Is the power outlet properly wired and polarized? Try 
another outlet to check for proper wiring and polarity.

■

Is this the first time the oven has been used? Turn any one 
of the surface burner knobs on to release air from the gas 
lines.

■

Is the electronic oven control set correctly? See 
“Electronic Oven Control” section.

■

On some models, is the Oven Lockout set? See “Oven 
Lockout” section.

■

Is the main or regulator gas shutoff in the off position? 
Contact a designated service technician or see the 
Installation Instructions.

■

This is normal and occurs when the oven burner cycles on 
and off to hold the set oven temperature.

■

Is propane gas being used? The appliance may have been 
converted improperly. Contact a trained repair specialist.

■

Is the air/gas mixture correct? Contact a designated 
service technician to check the air/gas mixture or see the 
Installation Instructions.

■

Does the oven temperature calibration need adjustment?
See “Oven Temperature Control” section.

■

Is the display showing “PF”? There has been a power 
failure. Touch OFF/CANCEL to clear the display. Reset the 
clock, if needed. See “Clock” section.

■

Is the display showing “F” followed by a number? Touch 
OFF/CANCEL to clear the display. If an “F” code appears 
again, contact a trained repair specialist.

■

Has a delay start been set? See “Timed Cooking” section.

■

Is the proper cookware being used? See “Cookware” 
section.

■

Is the control knob set to the proper heat level? See 
“Cooktop Controls” section.