HP DL360 G6 504635-421 ユーザーズマニュアル

HP Modular Power Distribution Units (mPDU), High Volt Model, 16A (200-240 VAC)
(WW)

NOTE:

NOTE:

NOTE:

NOTE: This PDU has a detachable input power cord and allows for adaptability to
country specific power requirements.

252663-B24

NOTE:

NOTE:

NOTE:

NOTE: Please see the following QuickSpecs for additional options including shorter
jumper cables and country specific power cords:

(Worldwide)
NOTE:

NOTE:

NOTE:

NOTE: For additional information on HP Power Distribution Units including
accessories please go to: 

 

NOTE:

NOTE:

NOTE:

NOTE: Please see the UPS and PDU cable matrix's on the HP Power Protection and
Management page. Under Power Cords, click on the "HP Power Cord Matrix" link.
That link will list cable descriptions, requirements, and specifications for UPS and PDU
units. Please see the following link: 

.

 

HP Rack Series

HP Rack Series

HP Rack Series

HP Rack Series

HP Rack 10000 G2 Series

HP Rack 10000 G2 Series

HP Rack 10000 G2 Series

HP Rack 10000 G2 Series (Carbon/Graphite Metallic)

HP 10642 G2 Pallet Universal Rack

AF001A

HP 10642 G2 Shock Universal Rack

AF002A

HP 10642 G2 1200mm deep Shock Rack

AF092A

HP 10647 G2 1200mm deep Shock Rack

AF094A

NOTE:

NOTE:

NOTE:

NOTE: It is mandatory to use a shock pallet when shipping racks with equipment
installed.
NOTE:

NOTE:

NOTE:

NOTE: Please see the QuickSpecs for additional information:

(Worldwide)

 

NOTE:

NOTE:

NOTE:

NOTE: For additional information regarding Rack Cabinets, please see the following
URL: 

 

NOTE:

NOTE:

NOTE:

NOTE: The increasing power of new high-performance processor technology requires
increased cooling efficiency for rack-mounted servers. The 10000 G2 Series Racks
provide enhanced airflow for maximum cooling, allowing these racks to be fully
loaded with servers using the latest processors.
CAUTION:

CAUTION:

CAUTION:

CAUTION: If a third-party rack is used, observe the following additional requirements
to ensure adequate airflow and to prevent damage to the equipment: Front and rear
doors: If your 42U server rack includes closing front and rear doors, you must allow
830 square inches (5,350 sq cm) of hole evenly distributed from top to bottom to
permit adequate airflow (equivalent to the required 64 percent open area for
ventilation). Side: The clearance between the installed rack component and the side
panels of the rack must be a minimum of 2.75 inches (7 cm).
CAUTION:

CAUTION:

CAUTION:

CAUTION: Always use blanking panels to fill all remaining empty front panel U-
spaces in the rack. This arrangement ensures proper airflow. Using a rack without
blanking panels results in improper cooling that can lead to thermal damage.
NOTE:

NOTE:

NOTE:

NOTE: For additional information, refer to the Setup and Installation Guide or the
Documentation CD provided with the server, or to the server documentation located
in the Support section at the following URL: 

.

 

Quick deploy rail system provides tool-free support for racks with square or round
mounting holes (including Compaq/HP 7000, 9000, 10000 G2 and HP series), with
an adjustment range of 24" - 36". The ambidextrous cable management arm can be
mounted on either the left or right side for improved cable management.

 

HP ProLiant DL360 Generation 6 (G6)

HP ProLiant DL360 Generation 6 (G6)

HP ProLiant DL360 Generation 6 (G6)

HP ProLiant DL360 Generation 6 (G6)

DA - 13235   Worldwide — Version 38 — October 14, 2011

Page 33