RuggedCom RUGGEDMAX WIN7000 ユーザーズマニュアル
1. Introduction
RuggedCom® RuggedMAX WiN7000
11
Installation Guide Rev1
1.3.3. Equipment Installation
Install the equipment in accordance with the electrical code relevant to the country of installation,
such as the National Electrical Code (NEC), ANSI/NFPA 70; the Canadian Electrical Code (CEC),
Part 1, CSA C22.1; and when applicable, the National Electrical Safety Code IEEE C2. Unless
marked or otherwise identified, the Standard for the Protection of Electronic Computer/Data
Processing Equipment, ANSI/NFPA 75, also applies.
such as the National Electrical Code (NEC), ANSI/NFPA 70; the Canadian Electrical Code (CEC),
Part 1, CSA C22.1; and when applicable, the National Electrical Safety Code IEEE C2. Unless
marked or otherwise identified, the Standard for the Protection of Electronic Computer/Data
Processing Equipment, ANSI/NFPA 75, also applies.
1.3.4. Radio Frequency (RF) Exposure
The WiN7000 is compliant with the requirements set forth in CFR 47, section 1.1307, addressing
Radio Frequency (RF) exposure from radio frequency devices as defined in OET Bulletin 65. The
emitted radiation should be as little as possible. To achieve minimum RF exposure, install the
WiN7000 when it is configured not to transmit and set it to operational mode remotely, rather
than enabling transmission by the installer on-site. For maintenance of the WiN7000, or other
operations which require RF exposure, the exposure should be minimized in time and according
to the regulations set by the FCC or the regulations relevant to the country of installation.
Radio Frequency (RF) exposure from radio frequency devices as defined in OET Bulletin 65. The
emitted radiation should be as little as possible. To achieve minimum RF exposure, install the
WiN7000 when it is configured not to transmit and set it to operational mode remotely, rather
than enabling transmission by the installer on-site. For maintenance of the WiN7000, or other
operations which require RF exposure, the exposure should be minimized in time and according
to the regulations set by the FCC or the regulations relevant to the country of installation.
1.3.5. Lightning Protection
When the WiN7000 is installed in an outdoor location, all indoor components (such as
Ethernet and power supply) should be connected through a lightning protector.
Ethernet and power supply) should be connected through a lightning protector.
Lightning protection protects people and equipment located indoors from lightning
that might strike the WiN7000 or its outdoor cables. Therefore, install the lightning
protector device indoors, as close as possible to the point where the cables enter
the building. The lightning protector can also be installed outdoors as long as the
cables that lead indoors are well protected from lightning between the protector and
the building entrance.
that might strike the WiN7000 or its outdoor cables. Therefore, install the lightning
protector device indoors, as close as possible to the point where the cables enter
the building. The lightning protector can also be installed outdoors as long as the
cables that lead indoors are well protected from lightning between the protector and
the building entrance.
1.3.6. Power Cord Protection
Route all power supply cords so that people cannot walk on them or place objects on or against
them. Walking on the cords or placing objects on or against the cords can damage the cords.
them. Walking on the cords or placing objects on or against the cords can damage the cords.
1.3.7. Servicing
Do not open the cover of this product to attempt service unless instructed by a RuggedMAX
certified technician. Refer all repairs to qualified service personnel. Removing the covers or
modifying any part of this device voids its warranty.
certified technician. Refer all repairs to qualified service personnel. Removing the covers or
modifying any part of this device voids its warranty.
RuggedCom does not endorse or support the use of proprietary third-party outdoor cable
assemblies not supplied by RuggedCom.
assemblies not supplied by RuggedCom.
Keep away from electric power lines.
You can be killed if the antennas are in close proximity to electric power lines. Carefully
read and follow all instructions in this manual. By nature of the installation, you may
be exposed to hazardous environments and high voltage. Use caution when installing
the outdoor system.
read and follow all instructions in this manual. By nature of the installation, you may
be exposed to hazardous environments and high voltage. Use caution when installing
the outdoor system.