Marantz AV Pre Tuner AV7005 ユーザーズマニュアル
52
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
SVENSKA
Set up speakers
around items indicate the settings.
1
Set up the
remote control unit
n
Set up the operation mode
Press
AMP
to set the remote control unit
to amplifier operation mode.
Press AMP
2
Connect the setup microphone.
[1/6]
STEP1 Preparation
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Start Auto Setup
Amp Assign
Channel Select
Auto Setup Start
AUTO SETUP
AUDYSSEY AUTO SETUP
MultEQ XT
ENTER
Enter
RETURN
Cancel
When the setup microphone is
connected, the following screen is
displayed.
connected, the following screen is
displayed.
This section provides the setup methods of speaker systems other than the 7.1-channel system
(with surround back speakers).
For the setup methods of the 7.1-channel system with surround back speakers, see “Simple
version”, “Set up speakers (Audyssey® Auto Setup)” (vpage 8) of “Simple version”.
(with surround back speakers).
For the setup methods of the 7.1-channel system with surround back speakers, see “Simple
version”, “Set up speakers (Audyssey® Auto Setup)” (vpage 8) of “Simple version”.
First install and connect the speakers to this unit.
Before Auto Setup measurement, the settings shown below can be made.
• Changing the amplifier assignment (Amp Assign)
• Changing the amplifier assignment (Amp Assign)
The signal output from the UNBALANCED and BALANCED PRE OUT SBL/SBR terminals of this unit can
be switched to match your speaker environment. (vpage 52 “Set up “Amp Assign””).
be switched to match your speaker environment. (vpage 52 “Set up “Amp Assign””).
• Setting the channels to be used (Channel Select)
If channels that are not to be used are set in advance, measurement for the set channels is skipped, and
measuring time can be reduced (vpage 52 “Set up “Channel Select””).
measuring time can be reduced (vpage 52 “Set up “Channel Select””).
n
Audio output from each PRE OUT terminal
PRE OUT Channel
UNBALANCED PRE
OUT terminal
FL/FR
C
SW1/SW2
SL/SR
SBL/SBR
HL/HR
WL/WR
BALANCED PRE
OUT terminal
FL/FR
C
SW1/SW2
SL/SR
SBL/SBR
---
---
Audio Output
Front A Center Subwoofer 1 /
Subwoofer 2 Surround
Surround
Back
*
Front Height /
Front B
Front Wide
*The output audio differs depending on the “Amp Assign” settings.
3
Set up “Amp Assign”
Use
ui
to select “Amp Assign”,
and then press
ENTER
.
[1/6]
STEP1 Preparation
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Set use of surround back ch. for your system
Amp Assign
Channel Select
Auto Setup Start
AUTO SETUP
AUDYSSEY AUTO SETUP
ENTER
Enter
RETURN
Cancel
MultEQ XT
4
Use
o
p
to select the configuration
of the connected speakers, and then
press
RETURN
.
Normal
Set
when
using
surround
back, front height or front wide
speakers. In this case, go to step
5.
speakers. In this case, go to step
5.
ZONE2
Set for connecting the speakers
for ZONE2.
for ZONE2.
ZONE3
Set for connecting the speakers
for ZONE3.
for ZONE3.
SPKR-C
Set for connecting the tweeter
of the front speaker to the
UNBALANCED and BALANCED
PRE OUT SBL/SBR terminals of
the power amp, and the woofer
of the front speaker to the FL/FR
terminals.
of the front speaker to the
UNBALANCED and BALANCED
PRE OUT SBL/SBR terminals of
the power amp, and the woofer
of the front speaker to the FL/FR
terminals.
5
Set up “Channel Select”
Use
ui
to select “Channel Select”,
and then press
ENTER
.
[1/6]
STEP1 Preparation
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Skip unused ch’s measurement for timesaving
Amp Assign
Channel Select
Auto Setup Start
AUTO SETUP
AUDYSSEY AUTO SETUP
ENTER
Enter
RETURN
Cancel
MultEQ XT
6
Use
ui
to select a channel.
Subwoofer Select for no subwoofers to be
used. In this case, go to step 7.
Surround
Back
Select for no surround back
speakers to be used. In this case,
go to step 8.
• “Surround Back” can be set when
speakers to be used. In this case,
go to step 8.
• “Surround Back” can be set when
“Amp Assign” is set to “Normal”.
Front
Height
Select for no front height speakers
to be used. In this case, go to step
9.
• “Front Height” can be set when
to be used. In this case, go to step
9.
• “Front Height” can be set when
“Amp Assign” is set to “Normal”.
Front Wide Select for no front wide speakers to
be used. In this case, go to step 9.
• “Front Wide” can be set when
• “Front Wide” can be set when
“Amp Assign” is set to “Normal”.
7
G
When “Subwoofer” is selected in
step 6H
Use
o
p
to select the item.
Measure Set for measuring a subwoofer.
Skip
Set for no measuring of a subwoofer.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
(Up/Down/Left/Right)
Confirm the setting
Return to previous menu
1.AV7005U_ENG.indd 52
2010/08/23 18:32:57