Vermont Castings 2460 取り扱いマニュアル

16

Your convection heater requires some assembly.  
Follow the directions carefully and refer to the parts 
diagram at the back of this manual.
CAUTION: The Dutchwest Convection Heater is very 
heavy. To prevent personal injury or damage, either to 
the stove or your home, have two or more people to 
help move it.

Remove all loose parts from the firebox and the ash 
pan.  Check to make sure all the parts are included and 
intact.  You should have received:
•  1 fully assembled heater body, (with catalytic burner 

installed at the factory)

•  4  legs
•  1 ash pan
•  1 probe thermometer
•  1 ceramic handle assembly
•  1 strip of Interam™ gasket (for the catalytic burner)
•  1 hardware bag,  containing the following parts:
  •  (3)  #10 x 1/2” sheet metal screws,  (to attach the 

chimney connector to the flue collar)

  •  (1)  1/8” Allen wrench, (to tighten the door latch) 
  •  (1)  5/32” Allen wrench, (to tighten the damper 

handle)

  •  (4)  washers, (used with the leg bolts to attach legs 

to the stove)   

  •  (1) door handle insert holder for storing the ceram-

ic handle assembly when it is not in use.

The four hex-head leg bolts have been installed in the 
appropriate holes in the bottom of the stove.
If any parts are missing or damaged, immediately notify 
your Dutchwest dealer for replacements. Do not install 
your stove without having all necessary parts or by us-
ing damaged parts.
* A Bottom Heat Shield is required in many instal-
lations. Refer to the floor protection information 
found in the Installation Section of this manual. 

NOTE: If heat shields are not properly installed and 
maintained, a house fire may result. For safety, follow 
these instructions. Contact local building officials about 
restrictions and installation inspection requirements in 
your area.
1.  Place the stove on its back. Tilt it carefully, it is 

heavy. Use 4 x 4 blocking to make it easier to tilt the 
stove. Protect surrounding flooring.

2.  The tops of the legs are slotted. Remove each leg 

bolt from the bottom of the stove and then replace it 
with a heat shield bracket and a washer. Place the 

ST431

dutchwest

attach legs

7/5/00   djt

Left Leg

Door 

Handle 

Holder

Heat 

Shield 

Bracket

Hex Head Bolt 

& Washer

ST431

Fig. 19  To attach the legs, remove the bolts from the stove 
bottom and reassemble with the handle holder, heat shield 
brackets (if necessary) and washers.

door handle insert holder on the bolt for the left rear 
or either front leg. (Fig. 19)

3.  Slide the leg into position around the bolt and fasten 

it finger-tight. Repeat this process for all four (4) 
legs. 

4.  Fasten, finger-tight, the bottom heat shield to the 

brackets using the four (4) 1/4-20 x 1/2” bolts with 
nuts. 

IMPORTANT: For heat shields with one side painted, 

the unpainted, reflective side should always face the 
stove to properly reflect the heat and fulfill its protec-
tive function. 

5.  Adjust the bracket’s position on each leg as needed 

until the shield fits. (Fig. 20)

6.  Use a 7/16” wrench to tighten the shield securely to 

the brackets and leg bolts securely to the stove.

7.  Carefully raise the stove onto its legs. 

������
�������������������
��������
����

Bottom Heat Shield

ST912

Fig. 20  Bottom heat shield in place on bottom of stove.