Tekkeon ET1000 ユーザーズマニュアル

 

1 

U S E R   G U I D E

 

ET1000 

Figure 1.  

ezTalker inserted into  

charging cradle 

EZ

T

ALKER

 by Tekkeon is a sleek cord-free headset that enables 

comfortable handsfree communication with your mobile phone. 

EZ

T

ALKER 

1000 works with your Bluetooth-ready mobile phone to provide clear, 
high-quality communication. 

While using your 

EZ

T

ALKER  

headset, you can store your mobile phone in 

your pocket, backpack, or briefcasejust about anywhere in close 
proximity that is convenient for you. 

Your ezTalker package includes  
the following:

  

!

 ezTalker Headset 

 

"

  Charging cradle with belt clip 

# 

Charger

 

%

 ezEarhook 

& 

ezFit Ring 

'

 Comfort Pad 

(

 User guide 

(not shown)

 

 

 
 

Before using ezTalker, you must: 

) 

Charge ezTalker 

) 

Pair ezTalker to your mobile phone 

) 

Fit ezTalker to your ear 

) 

Power ezTalker 

Directions for each of these activities are provided in the following four 
sections. Once these steps are completed, you will be ready to use 
ezTalker! 

Before using ezTalker, you must charge the headset for approximately 
two hours. When fully charged, the battery provides up to four hours of 
talk time and up to 168 hours of standby time. 

To Charge the Headset 

1.  Insert ezTalker into the charging cradle as 

shown.  

2.  Plug the charger into the charging jack on 

the right side of the charging cradle.  

3.  Plug the charger into a wall outlet. 

While the 

headset is charging, the amber LED on the 

headset will remain on. When the headset is 

fully charged, the amber LED will turn off. 

 

4. Unplug the charger cable from the wall outlet and the charging 

cradle.  

BATTERY INDICATION

: When the battery is low (less than 10% of 

capacity), the amber LED will flash and you’ll hear a double beep every  

32 seconds.

 

Pairing is the process of linking the headset with your Bluetooth mobile 
phone. Before using ezTalker with your mobile phone you must pair the 
devices. After this process is complete, you can use the headset only 

with its paired mobile phone. To use ezTalker with a different mobile 
phone, you must repeat the pairing process with the new mobile phone. 
In this case, the headset will no longer work with the original mobile 
phone. 

BEFORE YOU PAIR THE HEADSET

, 

ENSURE THAT THE BATTERY IS FULLY CHARGED

, 

AND 

REVIEW THE INSTRUCTIONS IN YOUR MOBILE PHONE USER GUIDE FOR PAIRING YOUR 
MOBILE PHONE TO A BLUETOOTH HEADSET

. 

To Pair the Devices 

1. Turn on the mobile phone and place it within 10 feet of the headset.  

2. Initiate the Bluetooth device-pairing (discovery) feature on the 

mobile phone. Refer to the mobile phone user guide for 
instructions on initiating this feature.  

3. With the headset turned off, press and hold the TALK button 

approximately five seconds, until the blue and amber LEDs flash 

alternately or until you hear the PAIRING tone.  

4. Release the TALK button. 

The headset is now in Pairing Mode

. 

5. Follow the mobile phone prompts, and when prompted for the 

passkey (also called passcode or BT PIN), enter 0000 (the ezTalker 
passkey).

 When pairing is complete, the headset will be placed in 

Standby Mode, ready to make and receive calls, the amber LED 

will turn off, and the blue LED will flash at two-second intervals.

 

! 

TALK Button 
Used for turning headset on/off, 
pairing, and making/receiving calls 

Volume Control 
Used to adjust the speaker volume 

and to mute the microphone 

Amber and Blue LEDs 
Provides visual indication of headset 
status: power on/off, pairing mode, 
muting mode, charging mode, and low 

battery 

Microphone 

Speaker 

"

# 

%

& 

'