Tascam RC-828 ユーザーズマニュアル

 

4 – 0.98

 

 key will go out. Pressing and holding the 

 

 key while pressing a 

 

 

key where no location point is stored (the indica-
tor is unlit) will have no effect.

To erase all location point memories, press and 
hold down the 

 

 key, and press the 

 

 key.

 

Turn on “auto play” mode by pressing this key 
(the indicator will light). The DTRS unit(s) con-
nected to the RC-828 will now start playing back 
when a location point accessed through the 

 

 keys [10] is reached. 

If “auto mode” is off (the indicator is off), the 
DTRS units will stop when the location point is 
reached.

 

This key and indicator duplicate the functions of 
the corresponding keys on the DTRS units. The 
first repeat point is stored in location memory 11, 
and the second repeat point in location memory 
12 (though memory 12 can be earlier than mem-
ory 11). These repeat points are independent of 
the repeat points stored in the DTRS units.

If these two points are less than five seconds apart, 
repeat play is not possible.

See the following sections of the manuals for 
operation of the repeat mode.

 

DTRS units are provided with a 

 

 con-

trol, allowing variable speed cueing to emulate 
“rock and roll” editing on open-reel machines.

The RC-828 allows this function to be carried out 
remotely, and also provides a jog dial, allowing 
precise cueing to frame accuracy.

The monitoring in these modes is determined by a 
combination of factors, including the 

 

 key [6]. See the flowchart in this manual for 

further details.

An important point to note is that, while most of 
the RC-828 controls can be used alongside the 
corresponding controls on the DTRS units (i.e. 
they can, with a few exceptions, such as the 

 

 key [5], be regarded as the same 

control), this key and indicator behave differently.

•

Pressing the 

 

 key on the RC-

828, or the 

 

 key on the first DTRS 

unit will enable the control on that unit. The 
indicator will light steadily, and the light on the 
other unit will flash.

•

Pressing the shuttling key on a unit where the 
indicator is flashing will enable the shuttling 
control on that unit and the indicator will light 
steadily. The steadily-lit indicator on the other 
unit will start to flash, and the shuttling control 
will be disabled.

•

Pressing the shuttling key on the unit where the 
indicator is steadily lit will turn off the indica-
tor on that unit, and the unit where the indicator 
is flashing. The shuttling controls of both units 
will now be disabled.

 

These transport controls duplicate the transport 
controls on the first DTRS unit at the “head” of 
the chain. Subsequent machines in the chain must 
be controlled by chasing the first unit (see 1.1.2, 
“Chase mode”).

However, if the first unit is chasing to timecode, 
pressing the 

 

 and 

 

 keys of the RC-828 

will have no effect. The 

 

 controls 

See the DTRS units’ manuals for details of the 
transport keys:

 

The supplied charts allow you to see what moni-
toring mode is in operation on a particular track or 
tracks, depending on the status of the DTRS units.

See the DTRS manuals for full details of monitor-
ing modes:

 

8.2.5

5-5

p. 22

—

 

2 [32]–[36]

2 [7]–[11]

p.10 26 – 30

—

 

7.1.2

9-1 (2)

p. 10 (19, 20) —