Bolens 930 SWE サービスマニュアル
Two-Way Chute Control™
The two-way chute control is located on the left side of
the dash panel and is used to control the distance of snow
discharge from the chute.
the dash panel and is used to control the distance of snow
discharge from the chute.
To change the upper chute angle to control the
distance that snow is thrown, pivot the lever forward
or backward.
distance that snow is thrown, pivot the lever forward
or backward.
Move the lever forward to pivot the upper chute down
and reduce the distance snow is thrown.
Move the lever rearward to pivot the upper chute
upward and increase the distance snow is thrown.
and reduce the distance snow is thrown.
Move the lever rearward to pivot the upper chute
upward and increase the distance snow is thrown.
Chute Directional Control
The chute directional control is located on the left side of
the snow thrower.
the snow thrower.
To change the direction in which snow is thrown,
crank clockwise to discharge to the left and
counterclockwise to discharge to the right.
crank clockwise to discharge to the left and
counterclockwise to discharge to the right.
•
•
•
•
Wheel Steering Controls
The left and right wheel steering controls are located on
the underside of the handles. Squeeze the right control to
turn right; squeeze the left control to turn left.
the underside of the handles. Squeeze the right control to
turn right; squeeze the left control to turn left.
NOTE:
Operate the snow thrower in open areas until you are
familiar with these controls.
Chute Clean-Out Tool
WARNING! Never use your hands to clear a
clogged chute assembly. Shut off engine and
remain behind handles until all moving parts
have stopped before unclogging.
clogged chute assembly. Shut off engine and
remain behind handles until all moving parts
have stopped before unclogging.
The chute clean-out tool is conveniently fastened to the
rear of the auger housing with a mounting clip. Should
snow and ice become lodged in the chute assembly during
operation, proceed as follows to safely clean the chute
assembly and chute opening:
rear of the auger housing with a mounting clip. Should
snow and ice become lodged in the chute assembly during
operation, proceed as follows to safely clean the chute
assembly and chute opening:
Release both the Auger Control and the Drive
Control.
Stop the engine by removing the ignition key.
Remove the clean-out tool from the clip which
secures it to the rear of the auger housing.
Use the shovel-shaped end of the clean-out tool
to dislodge and scoop any snow and ice which has
formed in and near the chute assembly.
Refasten the clean-out tool to the mounting clip on
the rear of the auger housing, reinsert the ignition
key and start the snow thrower’s engine.
While standing in the operator’s position (behind the
snow thrower), engage the auger control for a few
seconds to clear any remaining snow and ice from the
chute assembly.
Control.
Stop the engine by removing the ignition key.
Remove the clean-out tool from the clip which
secures it to the rear of the auger housing.
Use the shovel-shaped end of the clean-out tool
to dislodge and scoop any snow and ice which has
formed in and near the chute assembly.
Refasten the clean-out tool to the mounting clip on
the rear of the auger housing, reinsert the ignition
key and start the snow thrower’s engine.
While standing in the operator’s position (behind the
snow thrower), engage the auger control for a few
seconds to clear any remaining snow and ice from the
chute assembly.
1.
2.
3.
3.
4.
5.
6.
CHUTE DIRECTIONAL CONTROL
DISCHARGE
LEFT
DISCHARGE
RIGHT
CHUTE TILT
DOWN
CHUTE TILT
UP
DESCARGA
A LA
DERECHA
DESCARGA A
LA IZQUIERDA
INCLINACIÓN DEL
CANAL HACIA
ABAJO
INCLINACIÓN DEL
CANAL HACIA ARRIBA
CONTROL DIRECCIONAL DEL CANAL
1
s
ectiOn
4— c
OntrOls
and
f
eatures