Mellerware 20502 ユーザーズマニュアル

ページ / 4
SPECIFICATIONS
•  Big LCD display
•   Minimum capacity: 2.5kg
     Maximum Capacity: 150 kg
•  Division: 100g (0.2 lb) 
•  Auto Zero-Auto off
•  Low Battery / Overload Indication
•  Power: 1 Lithium battery (CR2032)
•  Equipped with High Precision Strain Gauge 
Sensor System (4 Sensors)
Preparations Before Use 
    
1.  Insert the Lithium battery (included). See figure 
1 (Note: Make sure battery is pushed all the 
way into its slot.  Also make sure + side of 
battery is facing out)
    
2.  Scale Setup: Place the scale on a hard flat 
surface. Tap the front corner (right or left) of 
the scale with your foot. The digit “0” will scroll 
across the display. Then the display will show 
“0.0”This indicates that the scale has been 
setup correctly.
a)  Note: This “Scale Setup” procedure applies 
only after installing a battery. After completing 
“Scale Setup”, it does not need to be 
performed again unless battery is removed 
and replaced.
b)  Note: If you step on the platform before “0.0” 
appears, you will not obtain a reading. If this 
happens, step off the scale, then wait for 
display to turn off, follow above steps to setup 
scale.
Scale Operation:
To measure weight, simply stand with both feet 
in the center of the scale’s glass platform.  Be 
sure to stand erect and remain still.  After 3 
seconds the display will flash your weight and 
then display it steady.
Note: If a weight less than 10kg is placed on the 
scale, the scale will not activate. To weigh 
something less than 10kg, activate the scale first 
by tapping the front corner (right or left) of the 
scale with your foot.
1.  When no weight is on the scale for 10 seconds, 
the scale will turn off automatically.
Getting Accurate Readings:
1.  If the scale has not been used for a long time, 
proceed as follows:
a)  First, step lightly on the front corner (right or 
left) of the scale first to activate the scale.
b)  Second, wait for the scale to turn off. Then you 
may use the scale normally.
2.  If the scale is moved, proceed as follows:
a)  remove the battery from the scale for 5 
seconds
b)  replace the battery
c)  follow “Scale Setup” instruction (listed in 
Preparations Before Use point 2 above)
3.  Place scale on flat hard surface.  Do not use 
scale on carpet because the reading will be 
inaccurate.
4.  If the reading appears inaccurate, please 
check if the battery and the contact point are 
well connected.  If scale has been in use for 
a long time, replace the battery and try again. 
If necessary, contact the local franchisers or 
contact our company.
Handling Tips:
1.  Store the scale horizontally.
2.  Do not overload the scale. 
3.  The scale is for home use only.
4.  Do not submerge scale in water. Use glass 
cleaner to clean glass platform of scale.
5.  Do not leave any objects on top of scale if the 
product is not to be used during a prolonged 
period of time. Also remove the battery to 
prevent it from being depleted or leaking.
6.  To avoid possible injury, do not stand on the 
edge of the platform.
7.  Place the scale in an area free from direct 
sunlight, heating equipment, high humidity, or 
extreme temperature change.
8.  To avoid slipping, make sure your feet and 
the glass platform of the scale are dry before 
standing on the scale.
9.  Please do not strike, hit or drop objects onto 
the glass platform, otherwise, the glass may 
break and cause serious injury. 
10. Strong magnetic fields may interfere with the 
operation of the scale. Avoid operating the 
scale in such areas.
Usage Notes:
1.  When the display shows ”Err”, it means that 
the scale is overloaded.
2.  When the display shows ”Lo”, it means that 
the battery is low. Please replace the battery as 
soon as possible.
3.  If scale display shows random digits or scale 
does not automatically shut off, proceed as 
follows:
a.  remove the battery for 10 seconds
b.  replace battery 
c.  follow “Scale Setup” instruction (listed in 
Preparations Before Use point 2 above)