Lynx L54PSR2NG オーナーマニュアル
36
lp connections
make sure the lp cylinder
valve is fully closed.
cylinder
cylinder
it is
possible for the valve to be
valve is fully closed.
valve is fully closed.
open without releasing gas
possible for the valve to be
possible for the valve to be
but, as soon as you start con-
open without releasing gas
open without releasing gas
necting the regulator, gas will
leak from the connection.
necting the regulator, gas will
necting the regulator, gas will
insert the regulator inlet into
the cylinder valve and turn the
black coupler clockwise until
the coupler is hand tight.
black coupler clockwise until
black coupler clockwise until
do
not over-tighten this connec-
the coupler is hand tight.
the coupler is hand tight.
tion.
To disconnect the coupler, first
To disconnect the coupler, first
make sure the main cylinder
To disconnect the coupler, first
To disconnect the coupler, first
valve is turned off.
make sure the main cylinder
make sure the main cylinder
grasp
the coupler and turn counter
rasp
rasp
clockwise.
the coupler and turn counter
the coupler and turn counter
the inlet will then
the coupler and turn counter
the coupler and turn counter
disengage.
always leak-test the connec-
always leak-test the connec-
tion after refilling or exchang
lways leak-test the connec-
lways leak-test the connec-
-
ing lp cylinders.
(see indeX:
“leak test” for further details.)
tt
gas lIne purgIng
you should pur
yy
ge the gas line
of air before attempting to
ou should pur
ou should purge the gas line
ge the gas line
light the grill.
of air before attempting to
of air before attempting to
make sure all grill controls
are in the “off” position.
slowly turn on the main
slowly turn on the main
gas supply.
push in the rotisserie knob
push in the rotisserie knob
and confirm that the igniter
is glowing. it is furthest
and confirm that the igniter
and confirm that the igniter
from the fuel source and
is glowing.
is glowing.
will completely purge the
lines.
will completely purge the
will completely purge the
it will take several
will completely purge the
will completely purge the
seconds for the burner to
light.
hold the knob on for
hold the knob on for
about 20 seconds to allow
the air in the system to
purge and the burner to
light
purge and the burner to
purge and the burner to
wait at least 5 minutes
after shutting off the
after shutting of
after shutting of
control before attempting
after shutting of
after shutting of
to light the burners.
control before attempting
control before attempting
FINAL CHECKS
leaK testIng
leak test
tt
procedure:
create a soapy solution
of 1 part soap and 3 parts
reate a soapy solution
reate a soapy solution
water.
Confirm that all control
Confirm that all control
knobs are in the off
position.
tur
tur
tt n on the fuel supply. for
natural gas, turn the valve
n on the fuel supply.
n on the fuel supply.
handle 1/4 turn to align
with the gas flow.
handle 1/4 turn to align
handle 1/4 turn to align
for l.p., tur
pp
n the cylinder
valve knob counter
clockwise one full rotation.
apply the soap solution
apply the soap solution
generously by paint brush
pply the soap solution
pply the soap solution
or squirt bottle on all con
generously by paint brush
generously by paint brush
-
nections and fittings.
or squirt bottle on all con
or squirt bottle on all con
if bubbles appear to
“grow” on any of the con-
f bubbles appear to
f bubbles appear to
nections, you have a gas
leak. immediately turn off
nections, you have a gas
nections, you have a gas
immediately
immediately
the gas supply.
fixing a gas leak
shut off the gas supply
tur
tur
tt n all grill controls to the
“on” position to purge
the grill of any gas build-
” position to purge
” position to purge
up, then turn the controls
back “
up, then turn the controls
up, then turn the controls
off
up, then turn the controls
up, then turn the controls
”.
Danger!
To prevent fire or explosion
hazard, DO NOT smoke or
To prevent fire or explosion
To prevent fire or explosion
allow any potential source
of ignition (sparks, electri
allow any potential source
allow any potential source
-
cal arcing, etc) in the area
of ignition (sparks, electri
of ignition (sparks, electri
while performing a leak
cal arcing, etc) in the area
cal arcing, etc) in the area
test. Leak tests should be
while performing a leak
while performing a leak
conducted outdoors only.
Never conduct a leak test
using fire or flame.
wash off the soapy solution
with cold water and dry.
off the soapy solution
off the soapy solution
tighten the loose joint, or
replace the faulty part with
ighten the loose joint, or
ighten the loose joint, or
manufacturer-recommend-
eplace the faulty part with
eplace the faulty part with
ed replacement parts.
do not attempt to repair
do not attempt to repair
the l.p. cylinder valve if it is
attempt to repair
attempt to repair
pp
damaged. the only way to
safely resolve a damaged
damaged.
damaged. he only way to
he only way to
cylinder is to Replace it.
it
it
Repeat the leak test to
ensure that no leaks are
Repeat the leak test to
Repeat the leak test to
present.
loW Heat burner
adjustment
for maIn brass burn-
ers, prosear™ and sIde
burners only!
do not adjust tHe ro-
tIsserIe burner.
the main brass burners and
side burners on your lynx
ll
grill featur
side burners on your
side burners on your
e an adjustable low
setting.
fluctuations in gas pressure,
fluctuations in gas pressure,
gas conversion and even in
luctuations in gas pressure,
luctuations in gas pressure,
the quality of the gas itself
gas conversion and even in
gas conversion and even in
may affect burner perfor-
the quality of the gas itself
the quality of the gas itself
mance at the “
may affect burner perfor-
may affect burner perfor-
low
may affect burner perfor-
may affect burner perfor-
” setting.
it could be either too high or
too low.
to adjust the bur
tt
ner low
setting:
o adjust the bur
o adjust the bur
make sure the grill is cool.
Remove racks and
Remove racks and
briquette trays so that you
can see the flames while
briquette trays so that you
briquette trays so that you
adjusting the burners.
light the burner and set
light the burner and set
it to “low”. (all the way
counter- clockwise).