Frigidaire FFSE5115P 仕様シート

USA

 • 

10200 David Taylor Drive

 • 

Charlotte, NC 28262

 • 

1-800-FRIGIDAIRE

 • 

frigidaire.com 

CANADA

 • 

5855 Terry Fox Way

 • 

Mississauga, ON L5V 3E4

 • 

1-800-265-8352

 • 

frigidaire.ca

FFSE5115P 07/13 

© 2013 Electrolux Home Products, Inc. 

Front Load Dryers

FFSE5115P   A / W     

7.0 Cu. Ft. D.O.E.  Electric 

Front Load Dryer Specifications
• 

Product Shipping Weight (approx.) – 140 Lbs.

• 

An electrical supply with grounded three-prong receptacle is required.

• 

Voltage Rating – 240V / 60 Hz / 30 Amps

• 

Single phase 3- or 4-wire cable, 240 Volt, 60 Hertz AC only electrical 

supply with ground required on separate circuit fused on both sides 

of line. (Do not use same circuit as washer.)

• 

Connected Load (kW Rating) @ 240 Volts = 5.4 kW

• 

Amps @ 240 Volts = 24 Amps

• 

Dryer MUST employ a 3-conductor NEMA 10-30 type SRDT or 

4-conductor NEMA 14-30 type SRDT or ST (as required), rated at  

240 volt AC minimum, 30 amp power supply cord marked for  

use with clothes dryers (not supplied).

• 

Grounding through neutral link prohibited in specific applications and 

certain locales, requiring use of 4-wire system. (For detailed electrical 

• 

Always consult local and national electric & plumbing codes.

• 

Can be installed alone, with or without optional 15" Pedestal Drawer, 

or stacked above matching Frigidaire® Washer, which requires 

installation of optional Dryer Stacking Kit. (For installation details, refer 

• 

Can be built in with matching Frigidaire® Washer in under-counter, 

recessed or closet installation. (Refer to Built-In Installations on this 

Product Installation Guide on web.) 

• 

Closet installation requires vented door with 2 unobstructed louvered 

openings, minimum 60 sq. in. each, located 3" from top and bottom 

of door. Full-length 120 sq. in. opening also acceptable. Allow 

additional 1" clearance between fronts of units and closed door.

• 

Do NOT install in area exposed to dripping water or outdoor weather 

conditions; where gasoline or other flammables are kept or stored; or 

where dryer comes in contact with curtains, drapes or anything that 

will obstruct flow of combustion and ventilation air.

• 

For garage installation, dryer MUST be located minimum 18" above floor.

• 

Floor MUST be solid with 1" maximum slope. Do NOT install on 

carpeted surface. 

• 

Dryer MUST exhaust to outside of building, NOT into any concealed 

space.

• 

Exhaust installation requires minimum 4"-diameter rigid or semi-rigid 

metal duct with approved, unobstructed vent hood having swing-out 

damper(s). If installing rigid metal duct (preferred), do not exceed 

MAXIMUM venting run length of 64 ft., allow deductions for elbows 

and vents. If installing semi-rigid metal duct, do not exceed MAXIMUM 

venting run length of 8 ft., always allow deductions for elbows and 

vents (Refer to Product Installation Guide on web for additional 

information). Do NOT use flexible plastic or metal foil duct and use 

shortest run possible.

• 

Leveling legs supplied to level dryer properly and reduce excessive 

noise and vibration.

• 

Water inlet hose for steam setting connects to cold water supply with  

“Y” connector and requires 3/4" clearance between back of unit and 

wall.

Optional Accessories
• 

Dryer Stacking Kit – (PN # STACKIT4X).

• 

15" Classic Silver Pedestal Drawer – (PN # CFPWD15A).

• 

15" Classic White Pedestal Drawer – (PN # CFPWD15W).

• 

Mobile Home Installation Kit – (PN # 137067200).

• 

Drying Rack – (PN # 137067300).