Maytag MDE18PDAYW インストール手順

28

The set-up code is indicated by the one or two left-hand 

characters. The set-up code value is indicated by the two or three 

right-hand characters.

Code Explanation
606  

REGULAR CYCLE PRICE

606 

 Represents the number of quarters (coin 1) needed 

to start the dryer; may adjust from 0–39 (See 

VALUE OF COIN 1 b.05). Advance from 0–39 by 

pressing the WHITES AND COLORS button. Factory 

default of 6 quarters = $1.50.

600  

PR MODELS: Factory default of 6 00, or 0 quarters.

• Press the PERM. PRESS button once to advance to next 

code.

705  

REGULAR DRY TIME

705 

 PD  MODELS:  Represents the number of minutes per 

quarter (coin 1). 

 

Factory default of 5 minutes per coin.

 

Example: 6 quarters x 5 minutes = 30 minutes.

 

 By pressing the WHITES AND COLORS button, value 

adjusts from 1–99 minutes.

• Press the PERM. PRESS button once to advance to next 

code.

800  

TYPE OF DRYER PRICING

800 

 Fixed Cycle with Top Off. For detailed description, see 

“General User Information.”

8FC 

 PR MODELS ONLY: Factory default of FC. Fixed Cycle. 

For detailed description, see “General User Information.” 

Use the DELICATES button to change this selection. 

• Press the PERM. PRESS button once to advance to

next code.

9 00  

 CYCLE COUNTER OPTION 

This option is either NOT SELECTED “OFF” or 

SELECTED “ON.”

9 00 

Not Selected “OFF.”

9 0C 

Selected “ON” and not able to be deselected.

• Press the DELICATES button 3 consecutive times

to select “ON.” Once selected “ON” it cannot be 

deselected.  

• Press the PERM. PRESS button once to advance to

next code.

If cycle counter (9 0C) is selected, the following is true: 

 

1 00  

Cycles in HUNDREDS 

 

1 02 = 200 

 

2 00  

Cycles in ONES   

 

2 25 =   25 

    

  

 

 

 

           TOTAL CYCLES = 225 

 

This is “VIEW ONLY” and cannot be cleared. 
• Press the PERM. PRESS button once to advance to next code.

Control Set-up Procedures

IMPORTANT: Read all instructions before operating.
The fabric setting buttons along with the digital display are used  

to set up the dryer controls. The display can contain 4 numbers 

and/or letters and a decimal point. These are used to indicate 

the set-up codes and related code values available for use in 

programming the appliance. 
How to Use the Buttons to Program the Controls
1.  The WHITES AND COLORS button is used to adjust the values 

associated with set-up code. Pressing the button will change 

the value by increments. Rapid adjustment is possible by holding 

down the button.

2.  The PERM. PRESS button will advance through the set-up 

codes. Pressing the button will advance to the next available 

set-up code. Holding down the PERM. PRESS button will 

automatically advance through the set-up codes at a rate faster 

than 1 per second.

3.  The DELICATES button is used to select or deselect options.

Start Operating Set-up

 

■

Single Load PD Models: Insert service door key, turn, and lift to 

remove service door. 

 

■

  Single Load PR Models: Once the debit card reader is installed 

(according to the reader manufacturer’s instructions), the 

set-up mode can be entered by inserting a manual set-up card 

(supplied by the reader manufacturer) into the card slot. If 

manual set-up card is not available, manual set-up mode can  

be entered by removing connector AA1 on the circuit board. 

IMPORTANT: The console must not be opened unless power is 

first removed from the dryer. To access connector AA1: 
g

 Unplug dryer or disconnect power. 

g

 Open console, disconnect plug on AA1, close console. 

g

 Plug in dryer or reconnect power. 

The dryer is now in the set-up mode. 
NOTE: This dryer is preset at the factory and does not require any 

programming. However, if you want to change the settings, follow 

the “Set-Up Codes” guide below.
■

   PD units are pre-set at the factory for fixed cycle price with top 

off. 

■

   PR units are pre-set for free cycle operation so they can be run 

without readers or coins. 

Set-Up Codes

 

■

  The PERM. PRESS button will advance you from code to code.

 

■

  The WHITE AND COLORS button will change the code value.

 

■

   The DELICATES button will select or deselect options.

PR MODELS: The set-up codes are the same as for the PD 

models except where noted.