Frigidaire FFTW1001PW 仕様シート

USA

 • 

10200 David Taylor Drive

 • 

Charlotte, NC 28262

 • 

1-800-FRIGIDAIRE

 • 

frigidaire.com 

CANADA

 • 

5855 Terry Fox Way

 • 

Mississauga, ON L5V 3E4

 • 

1-800-265-8352

 • 

frigidaire.ca

FFTW1001P

 

10/13 

© 2013 Electrolux Home Products, Inc. 

Top Load Washer

FFTW1001PW     

3.4 Cu. Ft. D.O.E. 

Top Load Washer Specifications
• 

Product Shipping Weight (approx.) – 118 Lbs.

• 

An electrical supply with grounded three-prong receptacle is required. 

The power supply circuit must be installed in accordance with current 

edition of National Electrical Code (ANSI/NFPA 70) and local codes & 

ordinances. (Do not use same circuit as dryer.)

• 

Voltage Rating – 120V / 60 Hz / 15 Amps

• 

Amps @ 120 Volts = 8.0 Amps

• 

Equipped with 120V 3-wire power supply cord, approx. 60" long.

• 

Always consult local and national electric & plumbing codes.

• 

To maximize detergent effectiveness, ambient temperature should 

never be below 60° F.

• 

Washer can be installed in recess or closet requiring 0" minimum 

installation clearance around sides and back of unit. To achieve 

0" minimum rear clearance when installed with dryer, dryer MUST 

be vented straight back. Closet installation requires additional 1" 

minimum clearance between front of unit and door. If washer and 

dryer are installed in same closet, door MUST be vented with 120 sq. in. 

minimum louvered opening, equally divided, located 3" from top and 

bottom of door. A louvered door with equivalent air openings for full-

length of door is acceptable. Air openings MUST remain unobstructed 

with door installed. (For additional installation details, refer to Product 

• 

Do NOT install in area exposed to dripping water or outdoor weather 

conditions; or where gasoline or other flammables, including 

automobiles, are kept or stored.

• 

Floor MUST be solid with 1" maximum slope. To minimize vibration  

or movement, reinforcement of floor may be necessary. Do NOT 

install on carpeted surface.

• 

Leveling legs supplied to level unit properly and reduce excessive 

noise and vibration.

• 

H/C water faucets MUST be installed within 42" of washer’s water  

inlet and MUST be 3/4" with threading for laundry hose connection  

to connect to 48" inlet hoses.

• 

Water pressure MUST be between 30 and 120 psi with NOT more 

than 10 psi pressure difference between hot and cold.

• 

Drain standpipe requires diameter of 1-1/4" min. and height of  

36" min. / 96" max. above floor, capable of eliminating 17 gallons  

per minute. Attached 61" drain hose can reach 74"-high standpipe.  

For higher standpipe, optional Drain Hose Extension Kit available.

• 

For manufactured or mobile home installation optional Mobile Home 

Installation Kit (PN # 137067200) required. (For specific installation 

Optional Accessories
• 

Mobile Home Installation Kit – (PN # 137067200).

• 

Drain Hose Extension Kit – (PN # 137098000).

Washer requires 0" minimum installation clearance 

around sides and back of unit. To achieve 0" minimum 

rear clearance when installed with dryer, dryer MUST 

be vented straight back. Closet installation requires 

additional 1" minimum clearance between front of unit 

and door. If washer and dryer are installed in same 

closet, door MUST be vented with 120 sq. in. minimum 

louvered opening, equally divided, located 3" from top 

and bottom of door. A louvered door with equivalent 

air openings for full-length of door is acceptable. 

Air openings MUST remain unobstructed with door 

installed. For additional installation details, refer to 

Product Installation Guide(s) on web.

H/C Water 

inlets 

  (rear) - 

48" hose 

length

42 

1

/

2

"

 60" 

Power 

cord 

(rear)

38 

1

/

2

"

27"

Drain 

hose 

retention 

clamp

(rear)

61" Hose 

length 

beyond

clamp

59"

29"

0"

 min.

0"

 min.

 20 

1

/

2

"

min.

Vented door

0" min.

1" min.

 60" 

sq. in.

min.

3"

 60" 

sq. in.

min.

3"