Viking FGNI515 インストールガイド
9
8
INSTALLATION OVERVIEW
The ice machine must:
• Be connected to cold, potable water.
• Be connected to a drain.
• Be connected to the proper power supply.
• Be able circulate air through the vents at the front.
• Be connected to cold, potable water.
• Be connected to a drain.
• Be connected to the proper power supply.
• Be able circulate air through the vents at the front.
Note: DO NOT build in so that the door is recessed. Door is meant to be flush with surronding cabinetry, but
not recessed.
not recessed.
INSTALLATION PARTS
The following installation parts are supplied with the ice machine:
2-Hinge covers
2-Hinge covers
2-Door stop pins
2-Hinge side covers
10-#8 sheet metal screws
2-Hole plugs
2-8-32 Machine screws
2-Hinge opening covers
4-Leveling leg caps
1-Upper door bracket (LH)
2-Black kickplate screws
1-Lower door bracket (LH)
1-Access panel button cover
ACCESSORY DOOR PANEL
The ice machine is supplied without a finished door panel. Accessory door panels are offered or a custom panel may
be used.
be used.
Accessory Door Panel Attachment
Note: If door swing is to be changed, it must be done before panel is attached.
Note: If door swing is to be changed, it must be done before panel is attached.
To attach a door panel:
The panel will be held on by 6 screws (supplied with door panel) and 2 machine screws (supplied with ice machine).
1. Remove the gasket and retain for later use.
2. If the door panel is stainless steel, remove any plastic covering the stainless steel panel.
3. Place the panel onto the outside of the door, and secure it
The panel will be held on by 6 screws (supplied with door panel) and 2 machine screws (supplied with ice machine).
1. Remove the gasket and retain for later use.
2. If the door panel is stainless steel, remove any plastic covering the stainless steel panel.
3. Place the panel onto the outside of the door, and secure it
to the door using two machine screws, located at the left
center and right center ( behind door gasket).
center and right center ( behind door gasket).
4. Fasten the panel to the door using the 6 screws (supplied
with door panel). In the hinge area, use the outermost screw
holes.
holes.
5. Place the covers over the hinge areas, and secure each cover
to the door using a screw (supplied with door panel).
6. Insert hole plug over screw installed in step 5 (supplied).
7. Return the gasket to its original position.
7. Return the gasket to its original position.
Air
intake
intake
Warm
air out
air out
2-3/4”
(7.0 cm)
(7.0 cm)
5-1/8”
(13.0 cm)
(13.0 cm)
1/4” (0.6 cm)
O.D. Copper Water
Inlet Compression
Fitting Provided
O.D. Copper Water
Inlet Compression
Fitting Provided
2-1/2”
(6.4 cm)
(6.4 cm)
7-1/2”
(19.1 cm)
(19.1 cm)
11-5/8”
(29.5 cm)
(29.5 cm)
115V
Power Cord
3-1/4”
(8.3 cm)
(8.3 cm)
Drain Access - Flexible Tubing
3/8” (.95 cm) I.D. Pump Model (included)
5/8” (1.6 cm) I.D. Gravity Model (not included)
3/8” (.95 cm) I.D. Pump Model (included)
5/8” (1.6 cm) I.D. Gravity Model (not included)
Drain / Electrical Location
Installation
Hole
plug
plug
Cover
Gasket
AIR FLOW
The machine takes in room temperature air at the lower right
front and forces warm air out the lower left front. Restricting the
airflow will adversely affect the ability of the ice machine to
make ice.
front and forces warm air out the lower left front. Restricting the
airflow will adversely affect the ability of the ice machine to
make ice.