Viking FGNI515 インストールガイド
17
16
If service is required, call your dealer or authorized service agency. The name of the authorized service agency can be
obtained from the dealer or distributor in your area.
obtained from the dealer or distributor in your area.
Have the following information readily available.
• Model number
• Serial number
• Date purchased
• Name of dealer from whom purchased
• Serial number
• Date purchased
• Name of dealer from whom purchased
Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized service agency,
or if you continue to have service problems, contact Viking Range, LLC at 1-888-(845-4641), or write to:
or if you continue to have service problems, contact Viking Range, LLC at 1-888-(845-4641), or write to:
VIKING RANGE, LLC
PREFERRED SERVICE
111 Front Street
Greenwood, Mississippi 38930 USA
Record the information indicated below. You will need it if service is ever
required. The model and serial number for your ice machine are located under
control panel in the upper compartment.
required. The model and serial number for your ice machine are located under
control panel in the upper compartment.
Model Number ____________________________________Serial Number ____________________________________________
Date of Purchase ____________________________________________________________________________________________
Date Installed _______________________________________________________________________________________________
Dealer’s Name ______________________________________________________________________________________________
Address ____________________________________________________________________________________________________
If service requires installation of parts, use only authorized parts to insure protection under the warranty.
KEEP THIS MANUAL FOR FUTURE REFERENCE.
Model and
Serial number
Serial number
The ice machine is supplied with a power cord. DO NOT remove the
grounding pin from the cord’s plug. DO NOT use extension cords. Follow all
codes. Connect the machine to its own 115 volt, 15 amp circuit.
grounding pin from the cord’s plug. DO NOT use extension cords. Follow all
codes. Connect the machine to its own 115 volt, 15 amp circuit.
FINAL INSTALLATION
1. If the electrical outlet for the ice maker is behind the unit, plug in the unit.
2. Snap the black caps over the bottom of the leveling legs.
3. Position the unit in the installation opening.
4. Turn on the water supply. Make sure that the ice maker is plugged in and
2. Snap the black caps over the bottom of the leveling legs.
3. Position the unit in the installation opening.
4. Turn on the water supply. Make sure that the ice maker is plugged in and
the power is on.
5. Slide unit into installation opening, paying careful attention to water supply
and drain connections. DO NOT kink!
6. Remove service panel for visual inspection.
7. Pour a couple of quarts of water into the ice storage bin; on drain pump equipped machines the drain pump should
7. Pour a couple of quarts of water into the ice storage bin; on drain pump equipped machines the drain pump should
start and water should pump out. Check for leaks.
8. Replace the service access panel and insert access panel button cover (supplied)..
9. Level the unit as needed by turning the leveling legs clockwise to raise the unit and counterclockwise to lower the
9. Level the unit as needed by turning the leveling legs clockwise to raise the unit and counterclockwise to lower the
unit.
INSTALLATION CHECKLIST
1. Has the unit been connected to the proper water supply?
2. Has the water supply been checked for leaks?
3. Has the unit been connected to a drain?
4. Has the drain been tested for flow and leaks?
5. Has the unit been connected to the proper electrical supply?
6. Has the unit been leveled?
7. Have all packing materials been removed from the machine?
8. Has the door covering been installed?
2. Has the water supply been checked for leaks?
3. Has the unit been connected to a drain?
4. Has the drain been tested for flow and leaks?
5. Has the unit been connected to the proper electrical supply?
6. Has the unit been leveled?
7. Have all packing materials been removed from the machine?
8. Has the door covering been installed?
Grounding type
wall receptacle
wall receptacle
Power Supply
with 3-prong
grounding plug
with 3-prong
grounding plug
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow these instructions could result in fire or electrical shock.
Electrical Connection
Service Information