Moen YB5422PB 仕様シート
2 5 3 0 0 A L MO E N D R I V E
N O R TH O L MS TE D , O H 4 4 0 7 0
C O R P O R A TE H E A D Q U A R TE R S : ( 8 0 0 ) 3 2 1 - 8 8 0 9
F A X: ( 8 0 0 ) 8 4 8 - 6 6 3 6
I N TE R N A TI O N A L : ( 4 4 0 ) 9 6 2 - 2 0 0 0
F A X: ( 4 4 0 ) 9 6 2 - 2 7 2 6
C U S TO ME R S E R V I C E ( U S A ) : 8 0 0 - 8 8 2 - 0 1 1 6
F A X: ( 8 8 8 ) 3 7 9 - 2 7 2 0
W W W . MO E N . C O M
Copyright Creative Specialties International
p
Towel Bar posts are constructed of
zinc. Bar is aluminum.
zinc. Bar is aluminum.
YB5422AN
– 24” Towel Bar
Antique Nickel Finish
YB5422AZ
– 24” Towel Bar
Antique Bronze
YB5422BN
– 24” Towel Bar
Brushed Nickel Finish
YB5422CH
– 24” Towel Bar
Chrome Finish
YB5422ORB
– 24” Towel Bar
Oil Rubbed Bronze Finish
YB5422PB
– 24” Towel Bar
Polished Brass Finish
YB5422WR
– 24” Towel Bar
Wrought Iron Finish
Cleaning Instructions:
Stock Number:______________________Double Towel Bar
By Creative Specialties
By Creative Specialties
Materials:
Stock Numbers:
Dimensions:
Double Towel Bar
YB5422
Kingsley
®
Technical Specification
To preserve the fine finish of this product, clean only with a soft
damp cloth. Dry well. Do not use commercial or abrasive cleaners.
damp cloth. Dry well. Do not use commercial or abrasive cleaners.
Literature #BA1482
Directions below are for installation into drywall. If installing product into
a stud, use the wood screws only.
1. Remove mounting posts from the product assemblies by loosening
each setscrew.
2. Position the mounting template on the wall in the desired location
3. Using a level, align the template and tape it to the wall.
4. Drill two 5/16” holes at each mounting post location that corresponds
to your product.
5. We recommend using the horizontal holes for drywall installation.
6. Remove the template from the wall.
7. Fold ends of the plastic toggle anchor together and insert into each
hole in the wall.
8. Lightly tap anchors until flush with the wall.
9. One at a time, insert plastic pin into each anchor and lightly tap to
activate anchor.
10. Remove pin and repeat on all anchors.
11. One at a time, place each mounting post over anchors (notch facing
downward) and insert screws through post into anchors.
12. Tighten screws.
13. Place assembly over the mounting posts with setscrew facing down
and tighten setscrew.
a stud, use the wood screws only.
1. Remove mounting posts from the product assemblies by loosening
each setscrew.
2. Position the mounting template on the wall in the desired location
3. Using a level, align the template and tape it to the wall.
4. Drill two 5/16” holes at each mounting post location that corresponds
to your product.
5. We recommend using the horizontal holes for drywall installation.
6. Remove the template from the wall.
7. Fold ends of the plastic toggle anchor together and insert into each
hole in the wall.
8. Lightly tap anchors until flush with the wall.
9. One at a time, insert plastic pin into each anchor and lightly tap to
activate anchor.
10. Remove pin and repeat on all anchors.
11. One at a time, place each mounting post over anchors (notch facing
downward) and insert screws through post into anchors.
12. Tighten screws.
13. Place assembly over the mounting posts with setscrew facing down
and tighten setscrew.
Installation Instructions: