Amana AGR5330BAW インストール手順
11
If the low flame needs adjusting:
1. Turn control knob to the “LO” setting and remove control
knob.
2. Insert a small flat-blade screwdriver into the valve stem. Turn
the valve adjusting screw to obtain the smallest flame that will
not go out when the control of a cold burner is quickly turned
from “HI” to “LO.” Turn right to decrease flame height. Turn
left to increase flame height. Repeat for other cooktop
burners as needed.
not go out when the control of a cold burner is quickly turned
from “HI” to “LO.” Turn right to decrease flame height. Turn
left to increase flame height. Repeat for other cooktop
burners as needed.
3. Replace control knob.
Check Operation of Oven/Broil Burner
Electronic oven control (on some models):
1. Open broiler door.
2. Press the “BAKE” pad.
■
The “BAKE” indicator will light.
■
“350” will appear in the display.
3. Press the START/ENTER pad.
■
The “TEMP” and “ON” indicators will appear.
■
The display will show the automatic countdown time
(10 minutes) needed to preheat the oven for selected
temperature.
(10 minutes) needed to preheat the oven for selected
temperature.
■
The oven burner should light in 20-40 seconds; this delay
is normal. The oven valve requires a certain time before it
will open and allow gas to flow. The oven burner will burn
until oven temperature has reached 350°F (175°C). After
20-40 seconds, the oven burner will begin to cycle on and
off to maintain the 350°F (175°C) temperature.
is normal. The oven valve requires a certain time before it
will open and allow gas to flow. The oven burner will burn
until oven temperature has reached 350°F (175°C). After
20-40 seconds, the oven burner will begin to cycle on and
off to maintain the 350°F (175°C) temperature.
Broil burner and oven burner are the same burner. Check the broil
function as follows:
function as follows:
1. Press the “BROIL” pad.
■
“525” will appear in the display.
■
The “BROIL” indicator will light.
2. Press the START/ENTER pad.
■
The oven burner should light in 20-40 seconds; this delay
is normal. The oven valve requires a certain time before it
will open and allow gas to flow.
is normal. The oven valve requires a certain time before it
will open and allow gas to flow.
To avoid damaging the hot surface igniter, do not insert any
object into the openings of the shield that surrounds the
igniter or clean that area.
object into the openings of the shield that surrounds the
igniter or clean that area.
3. Check the oven burner for proper flame. The flame should be
½" (1.3 cm) long, with inner cone of bluish-green. The outer
mantle should be dark blue and should be clean and soft in
character. No yellow tips (not enough air), blowing or lifting
(too much air) of flame should occur.
mantle should be dark blue and should be clean and soft in
character. No yellow tips (not enough air), blowing or lifting
(too much air) of flame should occur.
If the flame needs adjusting:
1. Turn the oven off. Wait for the oven burner to cool down.
2. Open oven door and remove oven racks and oven tray and
set aside.
3. Locate the air shutter near the rear wall of oven and loosen
the shutter screw.
4. Adjust the air shutter.
5. Turn the oven back on and check for proper flame. If the
flame is still not properly adjusted, turn the oven off, wait for
the oven burner to cool down and repeat Step 4 until flame is
properly adjusted.
the oven burner to cool down and repeat Step 4 until flame is
properly adjusted.
6. When the flame has been properly adjusted, turn the oven off,
wait for the burner to cool down.
7. Tighten the shutter screw.
8. Reinstall flame spreader and oven tray. Reinstall the oven
racks and close oven door.
9. Close the broiler door.
A. Valve stem
A
A. Oven tray (lift up at area shown to remove)
A. Shutter screw
B. Air shutter
B. Air shutter
A
A
A
B