Viking FPIM515 インストール手順
15
14
DOOR SWING CHANGE
The door can be attached to open with hinges on the left or right using new brackets shipped loose in
the ice bin. Retain all screws for re-use.
the ice bin. Retain all screws for re-use.
To change:
1. Remove inner screw holding each hinge to cabinet, loosen the outer screw.
2. Slide hinges to the side and remove door from cabinet. Remove outer screws
1. Remove inner screw holding each hinge to cabinet, loosen the outer screw.
2. Slide hinges to the side and remove door from cabinet. Remove outer screws
loosened in step 1 from both hinge brackets.
3. Remove two screws securing top panel to back, pull top panel back and
remove from cabinet.
4. Remove two screws at the top of the upper door hinge bracket and lift out of
the cabinet. Replace with the left hinge upper door bracket. Fasten it to the
cabinet using the original screws.
cabinet using the original screws.
5. Return the top panel to the cabinet and fasten it with the original screws.
6. Remove kickplate and front service panel.
7. Remove two front screws and two bottom screws holding the lower door
6. Remove kickplate and front service panel.
7. Remove two front screws and two bottom screws holding the lower door
hinge bracket to the cabinet. Replace with the left hinge lower door bracket.
Secure it using the original screws.
Secure it using the original screws.
8. Remove the upper hinge and move it to the door's opposite side, bottom
location. Secure using the original screws.
9. Remove the original lower hinge and move it to the door's opposite side,
upper location. Secure using the original screws. Note: If door panel is
attached, it must be removed to access hinge screws.
attached, it must be removed to access hinge screws.
10. Install a screw removed in step 2 in outer hole of upper and lower door brackets.
11. Attach the door to the cabinet using the original screws.
12. Return kickplate and front service panel to their original positions and attach
11. Attach the door to the cabinet using the original screws.
12. Return kickplate and front service panel to their original positions and attach
to the cabinet using the original screws.
DOOR STOP
•
In some situations the door can open too far and damage adjacent cabinets. To
prevent that, insert a stop into the provided hole in the top and bottom hinges
prevent that, insert a stop into the provided hole in the top and bottom hinges
•
Drive the pin into the hole until the head is against the hinge.
HINGE COVERS
After the hinge pins are installed (if used) and the door panel has been attached,
attach the hinge covers.
1. Slide the hinge cover over each hinge.
2. Attach the side cover over the hinge by peeling off the covering over the
attach the hinge covers.
1. Slide the hinge cover over each hinge.
2. Attach the side cover over the hinge by peeling off the covering over the
adhesive and placing it over the side of the hinge.
Note: If the hinges are used to secure the unit to the cabinet, DO NOT use the side covers.
KICKPLATE
The kickplate is black with a stainless steel covering. To use the stainless steel, no changes are required. To use the black,
remove the stainless steel covering by removing the two stainless steel screws. Replace with supplied black screws.
DO NOT remove stainless steel covering if ice machine is used outdoors.
remove the stainless steel covering by removing the two stainless steel screws. Replace with supplied black screws.
DO NOT remove stainless steel covering if ice machine is used outdoors.
INSTALLATION NOTES
Built In Situations: If a finished floor is to be installed in the area after the ice machine has been built in, shims the expected
thickness of the floor should be installed under the unit to keep the machine level with the planned floor level.
thickness of the floor should be installed under the unit to keep the machine level with the planned floor level.
Installations on a slab: Use a pump model and pump the water to the point of drainage. Pump models will pump 1 story
(10 feet) high.
(10 feet) high.
Installations over a crawl space or basement: Either gravity drain or pump model units may be used, if there is not
enough room behind the machine for a drain/waste receptacle, the drain will have to be below the floor.
Note: When installed in a corner, the door swing may be limited due to handle contact with the wall or cabinet face.
enough room behind the machine for a drain/waste receptacle, the drain will have to be below the floor.
Note: When installed in a corner, the door swing may be limited due to handle contact with the wall or cabinet face.
Outer screw
Inner screw
Upper
door
bracket
door
bracket
Screw
Lower
door
bracket
door
bracket
Bottom
screw
screw
Front
screw
screw
DOOR PANEL ATTACHMENT
Gasket
Accessory
Door Panel
Door Panel
Cover
Machine
Screw
Use Upper
Hole at the
Top
Use Lower
Hole at the
Bottom
Hole Plug
Insert door
stop pin
stop pin