Napoleon T495SBPK マニュアル
Correct Disposal Of This Product
This marking indicates that this product should not be disposed with other household wastes throughout the
EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle
it responsibly to promote the sustainable reuse of material resources. To return your used device, please use
the return and collection systems or contact the retailer where the product was purchased. They can take
this product for environmental safe recycling.
EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle
it responsibly to promote the sustainable reuse of material resources. To return your used device, please use
the return and collection systems or contact the retailer where the product was purchased. They can take
this product for environmental safe recycling.
Gas Cylinder
Use only gas cylinders, which meet national and regional codes. The minimum cylinder size for butane units
is 13kg, and for propane units is 6kg. Ensure that the cylinder can provide enough fuel to operate the appli-
ance. If in doubt, check with your local gas supplier.
is 13kg, and for propane units is 6kg. Ensure that the cylinder can provide enough fuel to operate the appli-
ance. If in doubt, check with your local gas supplier.
•
Use caution when handling the cylinder valve.
•
Never connect a cylinder, which does not meet local codes.
All cylinders 7kg or larger must be placed outside the enclosure (under the right side shelf) on level ground.
Cylinders smaller than 7kg (maximum size 465mm high by 306mm wide) may be placed inside the enclosure,
on the right side of the bottom shelf. Only cylinders connected to the appliance may be stored in the enclo-
sure, or close to the appliance. Spare cylinders must not be stored in the enclosure, or in close proximity of
an operating unit. Cylinders must not be exposed to extreme heat or direct sunlight.
Cylinders smaller than 7kg (maximum size 465mm high by 306mm wide) may be placed inside the enclosure,
on the right side of the bottom shelf. Only cylinders connected to the appliance may be stored in the enclo-
sure, or close to the appliance. Spare cylinders must not be stored in the enclosure, or in close proximity of
an operating unit. Cylinders must not be exposed to extreme heat or direct sunlight.
WARNING!
Ensure that the hose is routed to maintain proper clearance to the underside of the unit.
Hoses that contact high temperature surfaces may melt and leak, causing a fire.
Cylinder Connection: Ensure that the gas regulator hose is kink free. Remove the cap or plug from the cylin-
der fuel valve. Tighten regulator to cylinder valve. Leak test all joints prior to using the barbecue. A leak test
must be performed annually, and each time a cylinder is hooked up, or if a part of the gas system is replaced.
der fuel valve. Tighten regulator to cylinder valve. Leak test all joints prior to using the barbecue. A leak test
must be performed annually, and each time a cylinder is hooked up, or if a part of the gas system is replaced.
WARNING!
•
Do not route hose underneath drip pan.
•
Do not route hose between space in bottom shelf and back panel.
•
Do not route hose over top of back panel.
•
Ensure all connections are tightened using two wrenches. Do not use Teflon tape or pipe dope on any
hose connection.
hose connection.
•
Ensure the hose does not contact any high temperature surfaces, or it may melt and leak causing a fire.
•
Do not use enclosure to store excess hose, as there is a greater chance of the hose contacting a hot sur-
face, it may melt and leak causing a fire.
face, it may melt and leak causing a fire.
4
www.napoleongrills.com
Gas Hose
•
If the hose and regulator are not included by the manufacturer, then only hoses and regulators which
meet national and regional codes are to be used.
meet national and regional codes are to be used.
•
Ensure that the hose does not come into contact with grease, other hot drippings, or any hot surfaces on
the appliance.
the appliance.
•
Check hose regularly. In the case of rips, melting or wear, replace hose before using the appliance.
•
The recommended hose length is 0.5m. The hose must not be longer than 1.5m.
•
Ensure that the hose is twist and kink free when installed.
•
Replace the hose before expiry date printed on the hose.
EN