Electrolux E23BC78IPS オーナーマニュアル
17
Automatic Ice & Water Maker/Dispenser
Priming the water supply system
1 Begin filling the tank by pressing and holding
a drinking glass against the water dispenser
paddle.
paddle.
2 Keep the glass
in this position
until water
comes out of the
dispenser.
until water
comes out of the
dispenser.
It may
take about 1½
minutes.
minutes.
3 Continue
dispensing
water for about
three minutes to
flush the system and plumbing connections of
any impurities (stopping to empty the glass as
necessary).
water for about
three minutes to
flush the system and plumbing connections of
any impurities (stopping to empty the glass as
necessary).
Ice maker operation & care
After the refrigerator is installed properly and has
cooled for several hours, the ice maker can produce
ice within 24 hours. The ice maker will fill the ice bin
from the rear. You must dispense some ice to force
the ice forward in the bin. This will allow the bin to fill
completely.
cooled for several hours, the ice maker can produce
ice within 24 hours. The ice maker will fill the ice bin
from the rear. You must dispense some ice to force
the ice forward in the bin. This will allow the bin to fill
completely.
IMPORTANT
Your ice maker is turned on at the factory so it can work
as soon as you install your refrigerator. If you cannot
connect a water supply, set the ice maker’s On/Off icon
to Off and turn off the water supply valve; otherwise, the
ice maker’s fill valve may make a loud chattering noise
when it attempts to operate without water.
as soon as you install your refrigerator. If you cannot
connect a water supply, set the ice maker’s On/Off icon
to Off and turn off the water supply valve; otherwise, the
ice maker’s fill valve may make a loud chattering noise
when it attempts to operate without water.
CAUTION
For proper dispenser operation, recommended
water supply pressure should fall between 30 psi
and 100 psi. Excessive pressure may cause water
filter to malfunction.
water supply pressure should fall between 30 psi
and 100 psi. Excessive pressure may cause water
filter to malfunction.
NOTE
The water dispenser has a built-in device that shuts
off the water flow after three minutes of continuous
use. To reset this shutoff device, simply release the
dispenser paddle.
off the water flow after three minutes of continuous
use. To reset this shutoff device, simply release the
dispenser paddle.
NOTE
The ice maker also has a built-in plastic signal bale
arm that automatically stops ice production when the
ice bin is full. This signal arm should not be used to
manually stop the ice maker.
arm that automatically stops ice production when the
ice bin is full. This signal arm should not be used to
manually stop the ice maker.
IMPORTANT
Turning off the ice maker will result in existing ice
melting in the bin.
melting in the bin.
IMPORTANT
Turning off the ice maker will disable the ice
dispenser. You will still be able to dispense water.
dispenser. You will still be able to dispense water.
IMPORTANT
On occasion, unusually small ice cubes may be
noticed in the bucket or in dispensed ice. This could
occur in normal operation of the ice maker. If you start
seeing these more frequently, it may be an indication
of low water pressure or the water filter needs to
be replaced. As the water filter nears the end of its
useful life and becomes clogged with particles, less
water is delivered to the ice maker during each cycle.
Remember, if it’s been six months or longer since you
last changed your water filter, replace the water filter
with a new one. Poor quality household water may
require the filter to be changed more frequently.
noticed in the bucket or in dispensed ice. This could
occur in normal operation of the ice maker. If you start
seeing these more frequently, it may be an indication
of low water pressure or the water filter needs to
be replaced. As the water filter nears the end of its
useful life and becomes clogged with particles, less
water is delivered to the ice maker during each cycle.
Remember, if it’s been six months or longer since you
last changed your water filter, replace the water filter
with a new one. Poor quality household water may
require the filter to be changed more frequently.
Using the ice maker after installation
Before making ice for the first time, be sure to prime
the water supply system. Air in new plumbing lines
can result in two or three empty ice maker cycles.
Furthermore, if the system is not flushed, the first ice
cubes may be discolored or have an odd flavor.
the water supply system. Air in new plumbing lines
can result in two or three empty ice maker cycles.
Furthermore, if the system is not flushed, the first ice
cubes may be discolored or have an odd flavor.
Turning the ice maker on and off
Ice production is controlled by the ice maker’s
On/Off
icon on the control panel. Press and hold the “Ice Off”
icon for three seconds to turn the ice maker “
icon for three seconds to turn the ice maker “
ON” or
“
OFF”. When the ice maker is “OFF” the red LED above
the icon will be illuminated.
NOTE
Dispensed water is chilled. For colder water, add ice
to cup or container before dispensing water.
to cup or container before dispensing water.