Electrolux E36GC75PSS インストール手順
![Electrolux](https://files.manualsbrain.com/attachments/3404bb22dccbcfb6fc3ca6ee6cf2547381b94656/common/fit/150/50/424ff1215290c4147facb2112ed5c71f65e2af857b7bc4f69bdf4447be5b/brand_logo.png)
GAS COOKTOP INSTALLATION INSTRUCTIONS
5
The conversion must be performed by a qualified service
technician in accordance with the kit instructions and
all local codes and requirements. Failure to follow
instructions could result in serious injury or property
damage. The qualified agency performing this work
assumes responsibility for the conversion.
technician in accordance with the kit instructions and
all local codes and requirements. Failure to follow
instructions could result in serious injury or property
damage. The qualified agency performing this work
assumes responsibility for the conversion.
Failure to make the appropriate
conversion can result in serious personal injury and
property damage.
property damage.
Important:
Remove all packing material and literature
from cooktop before connecting gas and electrical
supply to cooktop.
supply to cooktop.
Install Pressure Regulator
Install the pressure regulator with the arrow on the
regulator pointing up toward the unit in a position
where you can reach the access cap.
regulator pointing up toward the unit in a position
where you can reach the access cap.
Do not make the connection too tight.
The regulator is die cast. Overtightening may crack the
regulator resulting in a gas leak and possible fire or
explosion.
regulator resulting in a gas leak and possible fire or
explosion.
Wall Outlet Location
Provide an Adequate Gas Supply
This cooktop is designed to operate on natural gas at 4"
(10,2 cm) of manifold pressure only.
(10,2 cm) of manifold pressure only.
A pressure regulator is connected in series with the
manifold on the cooktop and must remain in series with
the supply line.
manifold on the cooktop and must remain in series with
the supply line.
For proper operation, the maximum inlet pressure to
the regulator must be no more than 14" (35,6 cm) of
water column (W.C.) pressure.
the regulator must be no more than 14" (35,6 cm) of
water column (W.C.) pressure.
For checking the regulator, the inlet pressure must be at
least 1"(2,5 cm) (or 2,5 kPa) greater than the regulator
manifold pressure setting. The regulator is set for 4"
(10,2 cm) of manifold pressure, the inlet pressure must
be at least 5" (12,7 cm).
least 1"(2,5 cm) (or 2,5 kPa) greater than the regulator
manifold pressure setting. The regulator is set for 4"
(10,2 cm) of manifold pressure, the inlet pressure must
be at least 5" (12,7 cm).
The gas supply line to the range should be 1/2" (1,3 cm)
or 3/4" (1,9 cm) pipe.
or 3/4" (1,9 cm) pipe.
LP/Propane Gas Conversion
This appliance can be used with Natural gas or LP/
Propane gas. It is shipped from the factory for use with
natural gas.
A kit for converting to LP gas is supplied with your
cooktop. The kit is marked "FOR LP/PROPANE GAS
CONVERSION".
Propane gas. It is shipped from the factory for use with
natural gas.
A kit for converting to LP gas is supplied with your
cooktop. The kit is marked "FOR LP/PROPANE GAS
CONVERSION".
All connections must be wrench-tightened
Figure 5
Flare
Union
Flare
Union
GAS FLOW
Manual
Shutoff
Valve
Pressure
Regulator
On
Off
Flexible
Connector
Access
Cap
Nipple
Nipple
Assemble the flexible connector from the gas supply pipe
to the pressure regulator in the following order:
1. manual shutoff valve
2. 1/2" (1,3 cm) nipple
3. 1/2" (1,3 cm) flare union adapter
4. flexible connector
5. 1/2" (1,3 cm) flare union adapter
6. 1/2" (1,3 cm) nipple
7. pressure regulator
to the pressure regulator in the following order:
1. manual shutoff valve
2. 1/2" (1,3 cm) nipple
3. 1/2" (1,3 cm) flare union adapter
4. flexible connector
5. 1/2" (1,3 cm) flare union adapter
6. 1/2" (1,3 cm) nipple
7. pressure regulator
Use pipe-joint compound made for use with Natural and
LP/Propane gas to seal all gas connections. If flexible
connectors are used, be certain connectors are not
kinked.
LP/Propane gas to seal all gas connections. If flexible
connectors are used, be certain connectors are not
kinked.
Figure 4
Recommended
area for 120V
grounded
outlet on rear
wall.
area for 120V
grounded
outlet on rear
wall.
CENTRE
LINE
OF UNIT
LINE
OF UNIT
CENTRE
LINE
OF UNIT
LINE
OF UNIT
NOTE: If an
outlet is not
available, have
one installed
by a qualified
technician.
outlet is not
available, have
one installed
by a qualified
technician.
16"
(40,6 cm)
5"
(12,7 cm)
4"
(10,2 cm)