Electrolux EI24ID30QS オーナーマニュアル
7
Operating Instructions
Child Lock Controls/Air Dry
To prevent children from accidently changing the
dishwasher cycle or starting the dishwasher, lock
the dishwasher controls by pressing the AIR DRY
pad until Lock LED is on. The controls are locked
and no new selections can be made until the lock
is released. To unlock the controls, press the AIR
DRY pad until Lock LED turns off. If child lock is
activated the dishwasher will not work.
dishwasher cycle or starting the dishwasher, lock
the dishwasher controls by pressing the AIR DRY
pad until Lock LED is on. The controls are locked
and no new selections can be made until the lock
is released. To unlock the controls, press the AIR
DRY pad until Lock LED turns off. If child lock is
activated the dishwasher will not work.
Max Dry
MAX DRY is available on Auto, Heavy, and Normal,
cycles. The cycle time will increase when MAX
DRY option is selected.
cycles. The cycle time will increase when MAX
DRY option is selected.
O p e r a t i o n S e l e c t i o n
Delay
The Delay Start option allows you to automatically
delay starting your dishwasher from 2-4-6 hours.
delay starting your dishwasher from 2-4-6 hours.
Press DELAY pad until the LED of the desired
DELAY start is reached. If the door is opened while
the DELAY time is counting down, the DELAY LED
will blink.
DELAY start is reached. If the door is opened while
the DELAY time is counting down, the DELAY LED
will blink.
To cancel the DELAY option and begin the cycle
before the delay period is over, press the CANCEL
pad and then the START pad.
before the delay period is over, press the CANCEL
pad and then the START pad.
To start a cycle, press the START pad once and
close the door.
close the door.
To cancel a cycle at anytime, open the door and
press the CANCEL pad until you hear a tone.
When the door is opened, the last cycle selected
will be displayed. If desired, a new cycle can now
be selected by pressing CANCEL pad and upon
closing the door the cycle will begin.
press the CANCEL pad until you hear a tone.
When the door is opened, the last cycle selected
will be displayed. If desired, a new cycle can now
be selected by pressing CANCEL pad and upon
closing the door the cycle will begin.
Start
Cancel
E r r o r i n d i c a t i o n s
In the unlikely event the dishwasher malfunctions,
the 3 Delay LEDs blink constantly. If the Hi-
Temp LED blinks intermittently 1 time refer to
“Dishwasher won’t run or fi ll” and try to solve the
problem. If the Hi-Temp LED blinks 2 times refer
to “Dishwasher does not drain properly” and try to
solve the problem. If, after the check, the problem
remains, or if the LEDs are still blinking, contact
the Electrolux Customer Care Center at 1-877-
435-3287. They will be able to provide assistance
in troubleshooting the problem and/or locating an
authorized service technician, if needed.
the 3 Delay LEDs blink constantly. If the Hi-
Temp LED blinks intermittently 1 time refer to
“Dishwasher won’t run or fi ll” and try to solve the
problem. If the Hi-Temp LED blinks 2 times refer
to “Dishwasher does not drain properly” and try to
solve the problem. If, after the check, the problem
remains, or if the LEDs are still blinking, contact
the Electrolux Customer Care Center at 1-877-
435-3287. They will be able to provide assistance
in troubleshooting the problem and/or locating an
authorized service technician, if needed.
B l u e l i g h t i n d i c a t o r
When the BLUE LIGHT illuminates on the fl oor this
indicates that the wash cycle is complete.
indicates that the wash cycle is complete.
NOTE
Opening the door during normal operation will
only pause the selected cycle.
only pause the selected cycle.
NOTE
Your unit has DishSense
TM
Technology that is
used to understand how heavily soiled the dish
load is so the cycle can be automatically adjusted
to the appropriate response. This helps to
prevent energy waste. The sensor is calibrated
at the end of the cycle. For the fi rst cycle after
power is applied (when fi rst installed or after a
power failure) the sensor will not be calibrated
and so cannot determine the soil load. Therefore,
your unit will provide a response suitable for
heavy soils on the fi rst run after power is restored.
This will assure that whatever is loaded will get
cleaned. Energy use during this fi rst run may be
higher than would be typical.
load is so the cycle can be automatically adjusted
to the appropriate response. This helps to
prevent energy waste. The sensor is calibrated
at the end of the cycle. For the fi rst cycle after
power is applied (when fi rst installed or after a
power failure) the sensor will not be calibrated
and so cannot determine the soil load. Therefore,
your unit will provide a response suitable for
heavy soils on the fi rst run after power is restored.
This will assure that whatever is loaded will get
cleaned. Energy use during this fi rst run may be
higher than would be typical.