Electrolux E30GF74HPS インストール手順

Use pipe-joint compound made for use with Natural and

LP/Propane gas to seal all gas connections. If flexible 

connectors are used, be certain connectors are not 

kinked.
The supply line must be equipped with an approved 
manual shutoff valve. This valve should be located in 
the same room as the range and should be in a location 
that allows ease of opening and closing. Do not block 
access to the shutoff valve. The valve is for turning on or 
shutting off gas to the appliance.
Once regulator is in place, open the shutoff valve in the 
gas supply line. Wait a few minutes for gas to move 
through the gas line.
Check for leaks. After connecting the range to the gas 

supply, check the system for leaks with a manometer. 

If a manometer is not available, turn on the gas supply 

and use a liquid leak detector (or soap and water) at all 

joints and connections to check for leaks. Leaks will be

indicated by bubbles appearing at the connections or 

joints.

Assemble the flexible connector from the gas supply pipe 
to the pressure regulator in the following order:
1.  Manual shut-off valve (not supplied)
2.  1/2" nipple (not supplied)
3.  1/2" flare union adapter (not supplied)
4.  Flexible connector (not supplied)
5.  1/2" flare union adapter (not supplied)
6.  1/2" nipple (not supplied)
7.  Pressure regulator (supplied)

When shipped from the factory, this unit is designed 

to operate on 4"(10,16 cm) water column (1.0 kPa) 

Natural gas manifold pressure. A convertible pressure 

regulator is connected to the range manifold and MUST 

be connected in series with the gas supply line. The gas 

connector is located as shown on figure 2. It is accessible 

from front of the range.
For proper operation, the maximum inlet pressure to 

the regulator should be no more than 14"(35,56 cm) of 

water column pressure (3.5 kPa). 
The inlet pressure to the regulator must be at least 1" 

(.25 kPa) greater than the regulator manifold pressure 

setting. The regulator is set for 4"(10,16 cm) water 

column (1.0 kPa) Natural gas manifold pressure; the inlet 

pressure must be at least 5"(12.60 cm) water column 

(1.25 kPa) Natural gas. For LP/Propane gas, the regulator 

must be set for 10"(25,4 cm) water column (2.5 kPa) 

manifold pressure; the inlet pressure must be at least 

11"(27,9 cm) water column (2.75 kPa).
The supply line should be equipped with an approved 

shutoff valve (see Figure 4 and 5). This valve should be 

located in the same room as the range and should be 

in a location that allows ease of opening and closing. 

Do not block access to the shutoff valve. The valve is for 

turning on or shutting off gas to the appliance. Open the 

shutoff valve in the gas supply line. Wait a few minutes 

for gas to move through the gas line.
The gas supply between the shutoff valve and the 
regulator may be connected by rigid piping or by CSA-
approved flexible metallic union-connected piping where 
local codes permit use.
The gas supply piping can be through the side wall of 
the right cabinet. The left side cabinet is an ideal location 
for the main shutoff valve, if the range is installed within 
cabinet storage space

The regulator is already installed on the appliance.

 Do not make the connection too tight. 

The regulator is die cast. Overtightening may crack the 
regulator resulting in a gas leak and possible fire or 
explosion.

The gas supply line to the shutoff valve should be 

1/2"(1,27 cm) or 3/4"(1.9 cm) solid pipe.
The user must know the location of the main shutoff 
valve and have easy access to it.
When using flexible gas conduit on the range, allow 

sufficient slack to pull the range outside the cutout for 

cleaning or servicing.
NOTE:  Do not allow the flexible conduit to get pinched 
between the wall and the range. 

Flare

Union

Flare

Union

GAS FLOW

Manual

Shutoff

Valve

Pressure

Regulator

On

Off

Flexible

Connector

Access

Cap

Nipple

Nipple