Radio Shack 273-1668 プリント
13.5/30VDC • 1000mA
AC-to-DC POWER ADAPTER
273-1668
RF Emission Information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Modifying or tampering with your 13.5/30VDC 1000mA AC-to-DC
Power Adapter’s internal components can cause a malfunction, which
might invalidate its warranty and void your FCC authorization to
operate it.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Modifying or tampering with your 13.5/30VDC 1000mA AC-to-DC
Power Adapter’s internal components can cause a malfunction, which
might invalidate its warranty and void your FCC authorization to
operate it.
©2007.
RadioShack Corporation.
All rights reserved.
RadioShack and RadioShack.com
are trademarks used by
RadioShack Corporation.
11A07
273-1668
Printed in China
Using your Adapter
1. Plug the correct size
Adaptaplug onto the jack at
the end of the adapter’s cord.
the end of the adapter’s cord.
• If your device’s DC input jack is marked
, align TIP
on the adapter’s jack with
+
on the Adaptaplug (shown).
• If the DC input jack is marked
, align TIP on the
adapter’s jack with – on the Adaptaplug.
CAUTION: Be sure to set the correct tip polarity. Incorrect polarity
can damage your device or the adapter.
2. Plug the Adaptaplug into your device’s DC input jack.
3. Set the adapter’s voltage switch to the correct setting.
4. Plug the adapter into an easily accessible power outlet located
3. Set the adapter’s voltage switch to the correct setting.
4. Plug the adapter into an easily accessible power outlet located
near the equipment.
Cautions:
• If this adapter is not compatible with the voltage and current
requirements of your portable device, it can result in PERMANENT
DAMAGE to the device.
DAMAGE to the device.
• Before using, consult the User’s Guide or the rating label on your
device to make sure it requires 13.5 or 30 volts DC.
• The power adapter’s current (1000mA) must be equal to or more
than the current needed by your portable device.
• Before charging cell phones, make sure the cell phone
specifications are supported by this power adapter.
• Never operate the adapter if it has been damaged in any way. Do
not disassemble it.
WARNING: To prevent fire or shock hazard, do not expose the
adapter to rain or other moisture.
CAUTION: The total combined current for accessories plugged into
this adapter must not exceed 1000mA.
adapter to rain or other moisture.
CAUTION: The total combined current for accessories plugged into
this adapter must not exceed 1000mA.