Elite Video SC-63 ユーザーズマニュアル
68
09
Using other functions
MULTI-ZONE remote controls
Press the remote control’s ZONE 2 or ZONE 3 to operate the corresponding zone.
The following table shows the possible MULTI-ZONE remote controls:
The following table shows the possible MULTI-ZONE remote controls:
Button(s)
What it does
u
Switches on/off power in the sub zone.
INPUT SELECT
Use to select the input function in the sub zone.
Input function buttons
Use to select the input function directly (this may not work for some functions) in the sub
zone.
zone.
VOLUME +/–
<a>
<a>
Use to set the listening volume in the sub zone.
MUTE
<a>
<a>
Mutes the sound or restores the sound if it has been muted (adjusting the volume also
restores the sound).
restores the sound).
a The volume cannot be adjusted on the receiver if Volume Level at ZONE 2 Setup under ZONE Setup is set to –40 dB Fixed or
0 dB Fixed.
Making an audio or a video recording
You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to
the receiver (such as a CD player or TV).
Keep in mind you can’t make a digital recording from an analog source or vice-versa, so make sure the compo-
nents you are recording to/from are hooked up in the same way (see
the receiver (such as a CD player or TV).
Keep in mind you can’t make a digital recording from an analog source or vice-versa, so make sure the compo-
nents you are recording to/from are hooked up in the same way (see
Connecting your equipment
on
page 18
for
more on connections).
! The receiver’s volume, Audio parameters (the tone controls, for example), and surround effects have no effect
! The receiver’s volume, Audio parameters (the tone controls, for example), and surround effects have no effect
on the recorded signal.
! Some digital sources are copy-protected, and can only be recorded in analog.
! Some video sources are copy-protected. These cannot be recorded.
Since the video converter is not available when making recordings (from the video OUT jacks) make sure to use
the same type of video cable for connecting your recorder as you used to connect your video source (the one you
want to record) to this receiver. For example, you must connect your recorder using Component video if your
source has also been connected using Component video.
! Some video sources are copy-protected. These cannot be recorded.
Since the video converter is not available when making recordings (from the video OUT jacks) make sure to use
the same type of video cable for connecting your recorder as you used to connect your video source (the one you
want to record) to this receiver. For example, you must connect your recorder using Component video if your
source has also been connected using Component video.
1 Select the source you want to record.
Use the input function buttons (or INPUT SELECT).
2 Prepare the source you want to record.
Tune to the radio station, load the CD, video, DVD etc.
3 Select the input signal according to the signal to be recorded.
Use the remote control’s SIGNAL SEL button.
4 Prepare the recorder.
Insert a blank tape, MD, video etc. into the recording device and set the recording levels. Refer to the instructions
that came with the recorder if you are unsure how to do this. Most video recorders set the audio recording level
automatically-check the component’s instruction manual if you’re unsure.
that came with the recorder if you are unsure how to do this. Most video recorders set the audio recording level
automatically-check the component’s instruction manual if you’re unsure.
5 Start recording, then start playback of the source component.
Network settings from a web browser
Network settings and Pandora or SiriusXM account settings can be made using the browser on a computer con-
nected to the same LAN as the receiver.
nected to the same LAN as the receiver.
1 Turn on the computer’s power and launch the Internet browser.
2 Input the receiver’s IP address into the browser’s address input field.
2 Input the receiver’s IP address into the browser’s address input field.
For example, if the receiver’s address is 192.168.0.2, input “http://192.168.0.2/”. Check the receiver’s IP address at
Checking the Network Information
on
page 88
.
When connected with the receiver, the Web Control screen appears in the browser.
3 When the Web Control screen appears, select the item you want to set.
Using the sleep timer
The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use the remote control to set the sleep timer.
worrying about the receiver being left on all night. Use the remote control to set the sleep timer.
% Press
to the receiver operation mode, then press SLEEP repeatedly to set the sleep
time.
30 min
60 min
Off
90 min
! You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle
through the sleep options again.
! The sleep timer is valid for all zones. If any zone is on, the sleep timer continues functioning.
Dimming the display
You can choose between four brightness levels for the front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
display automatically brightens for a few seconds.
% Press
to the receiver operation mode, then press DIMMER repeatedly to change the
brightness of the front panel display.
! You can also choose to turn the display off. In this case, the FL OFF indicator lights.
Checking your system settings
Use the status display screen to check your current settings for features such as surround back channel process-
ing and your current MCACC preset.
ing and your current MCACC preset.
1 Press
to the receiver operation mode, then press STATUS to check the system
settings.
The front panel display shows each of the following settings for three seconds each: Input Source
d Sampling
Frequency
d MCACC preset d ZONE 2 input d ZONE 3 input.
2 When you’re finished, press STATUS again to switch off the display.