Techno Source 90660 ユーザーズマニュアル

Page 13

back cover 

Page 11

Page 12

From the Game Screen, start a 2-player game by pressing the thumb button once, or 
until you see only 2P on the screen. Then press and hold the thumb button to confirm 
your selection.

IM-90660

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void 
the user’s authority to operate the equipment. 

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residental installation. This equipment generates, uses and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a particular installation. If 
this equipment does cause harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of 
the following measures:

   Reorient or relocate the receiving antenna. 
   Increase the separation between the equipment and receiver.
   Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
   Consult the dealer or experienced radio/TV technician for help.

BATTERY, SAFETY AND PRECAUTION INFORMATION

2-PLAYER GAME

Turn to Pg. 3 for instructions on how to CHOOSE YOUR CHARACTER.

    NOTE: Players cannot choose the same character. Once a character has been selected, the  
    universal symbol for “NO” (  ) will appear over that character screen to let you know that it 
    cannot be selected. The second player will have to select one of the 3 remaining characters.

Turn to Pg. 4 to the WEAPONS section for further instructions on how to play Battletronics™.

If units become unlinked while playing, the LINKING screen will appear and prompt you to line up 
the 2 Battletronics™, with IR transmitters facing one another. After several seconds, the units will 
relink and the game will continue where it left off. 

The IR range for Battletronics™ is 6in to 6ft. Players should be within 6ft. of each other when playing 
and no closer than 6in. apart.

Play Battletronics™ indoors. Sunlight or strong lights may interfere with the infrared receiver.

Other IR devices, such as TV remote controls, may interfere with the IR signal. If a problem occurs, 
move away from the interfering device.

Battletronics™ is a 1 or 2-player game. No more than 2 Battletronics units can participate in a game. 
Additional units may interfere with the current game.

Both players will now see a screen with LINK WEB SHOOTERS. Position 
your arm so that both units are facing one another (IR transmitters should 
be pointing at one another). A LINKING screen will appear to let you know 
that the units are linking up.

Each Battletronics™ has an IR transmitter and receiver that allows 
two units to link up and communicate. When playing, it is important 
that the IR transmitters face one another; otherwise, the units will 
unlink and the game will end.  

When the units have linked up, you will hear “Choose Your Character”. One unit may 
register before the other, but the game will not continue until both units are fully linked.

BATTERY INSTALLATION

• Unscrew the battery cover with a Phillips screwdriver.

• Insert 3 "AAA" (1.5V) batteries with the positive (+) and negative (-) 

ends facing in the proper direction as indicated in the battery 

compartment. (see Fig. 1)

• Replace the cover.

CARING FOR YOUR DEVICE

• If the display becomes dim or malfunctions, replace the batteries.

• After replacing batteries, press any button to start the game to 

ensure proper functioning. (In most cases, game malfunctions 

are due to weak batteries.)

• In an environment with electrostatic discharge, the product may 

malfunction and lose memory. In this case, press buttons A and 

B to reset the unit.

Fig. 1

FOR MORE INFORMATION, VISIT US AT:

FOR MORE INFORMATION, VISIT US AT:

WWW.TECHNOSOURCEUSA.COM

WWW.TECHNOSOURCEUSA.COM

FOR MORE INFORMATION, VISIT US AT:

WWW.TECHNOSOURCEUSA.COM

11

13

12