Vermont Casting RADVTCBD ユーザーズマニュアル
12
12
Radiance Direct Vent Gas Heater
20012697
Venting Requirements and Options
Approved Vent System Components
The Radiance Heater must be vented to the outdoors
through an adjacent exterior wall or through the roof. The
venting system must be comprised of the appropriate
listed venting components specified on this page. These
parts are available from DuraVent Corporation, Selkirk
Corporation or your Vermont Castings Dealer.
See Figure 4 for dimensions relevant to the standard
minimum-vent kits.
The Radiance Heater must be vented to the outdoors
through an adjacent exterior wall or through the roof. The
venting system must be comprised of the appropriate
listed venting components specified on this page. These
parts are available from DuraVent Corporation, Selkirk
Corporation or your Vermont Castings Dealer.
See Figure 4 for dimensions relevant to the standard
minimum-vent kits.
Simpson DuraVent Components
www.duravent.com
Phone: 1-800-835-4429, Fax: 1-707-446-4740
Phone: 1-800-835-4429, Fax: 1-707-446-4740
Minimum Horizontal Vent Kit
2792
Starter Pipe Assembly (incl. inner & outer sections)
2768*
90° Elbow, Blk.
46DVA-E90B*
45° Elbow, Gal.
46DVA-E45
6” Straight, Blk.
46DVA-06B*
9” Straight, Blk.
46DVA-09B
11” - 14⁵⁄₈” Adjustable Straight Section
46DVA-08AB
12” Straight
46DVA-12
24” Straight
46DVA-24B*
36” Straight
46DVA-36B
48” Straight
46DVA-48
Horizontal Vent Cap
46DVA-HC*
Wall Plate
46DVA-DC
Vinyl Siding Shield
46DVA-VSS
Snorkel Termination - 14”
46DVA-SNK14
Snorkel Termination - 36”
46DVA-SNK30
Wall Strap
46DVA-WS
Cathedral Ceiling Support Box
46DVA-CS
Storm Collar
46DVA-SC
Firestop Spacer
46DVA-FS
Flashing 0/12 - 6/12
46DVA-F6
Flashing 6/12 - 12/12
46DVA-F12
Steel Chimney Conversion Kit
Kit A (6⁵⁄₈” - 8⁵⁄₈”)
Kit A (6⁵⁄₈” - 8⁵⁄₈”)
46DVA-KCA
Kit B (6⁵⁄₈” - 10¹⁄₂”)
46DVA-KCB
Kit C (6⁵⁄₈” - 13”)
46DVA-KCC
Masonry Chimney Conversion Kit
46DVA-KMC
Vertical Termination Cap (High Wind)
46DVA-VCH
Vertical Termination Cap (Low Profile)
46DVA-VC
*Included in Minimum Horizontal Vent Kit #2792
All DuraVent Straight vent pipe sections have a net length 1¹⁄₂”
(37mm) less than the nominal dimension; i.e., a 6” (152mm)
Straight pipe section has an effective length of 4¹⁄₂” (115mm).
All DuraVent Straight vent pipe sections have a net length 1¹⁄₂”
(37mm) less than the nominal dimension; i.e., a 6” (152mm)
Straight pipe section has an effective length of 4¹⁄₂” (115mm).
Selkirk Corporation Vent Components
www.selkirkcorp.com
1301 W. President George Bush Highway Ste. 330
Richardson, TX 75080
Phone: 1-800-992-8368, Fax: 1-877-393-4145
1301 W. President George Bush Highway Ste. 330
Richardson, TX 75080
Phone: 1-800-992-8368, Fax: 1-877-393-4145
Appliance Adapter
4DT-AAV
90° Elbow, Blk.
4DT-EL90B
45° Elbow, Blk.
4DT-EL45B
6” Straight, Blk.
4DT-06B
9” Straight, Blk.
4DT-09B
4” - 10” Adjustable Straight Section, Blk.
4DT-AJ12
12” Straight, Blk.
4DT-12B
18” Straight, Blk.
4DT-18B
24” Straight, Blk.
4DT-24B
36” Straight, Blk.
4DT-36B
48” Straight, Blk.
4DT-48B
Horizontal Vent Cap
4DT-HC
Wall Plate
4DT-WT
Vinyl Siding Shield
4DT-VS
Snorkel Termination - 14”
4DT-ST14
Snorkel Termination - 36”
4DT-ST36
Wall Strap
4DT-WS/B
Cathedral Ceiling Support Box
4DT-CCS
Storm Collar
4DT-SC
Firestop Spacer
4DT-FS
Flashing 0/12 - 6/12
4DT-AF6
Flashing 6/12 - 12/12
4DT-AF12
Steel Chimney
Horizontal Kit A
Horizontal Kit A
4DT-HKA
Horizontal Kit B
4DT-HKB
Vertical Kit
4DT-VKC
Masonry Chimney Kit
4DT-MCK