Aussie pmn ユーザーズマニュアル
· Always perform a leak test before each use.
· Leak test must be performed in a well ventilated
· Leak test must be performed in a well ventilated
area.
· Never perform a leak test on a grill while in use or
hot.
· If you detect a gas leak that cannot be corrected
by using the leak test procedures below, do not
use the LP gas grill.
use the LP gas grill.
· Never smoke or have an open flame near the grill
during a leak test.
Supplies Needed for a Leak Test
Clean paint brush, water, and dishwashing liquid.
How to perform a leak test (See Step 10 of Assembly
Instructions for leak test diagrams.)
Clean paint brush, water, and dishwashing liquid.
How to perform a leak test (See Step 10 of Assembly
Instructions for leak test diagrams.)
WARNING! Never use an open flame to test for gas
leaks.
leaks.
1)Use an LP Cylinder equipped with an OPD (Overfill
Prevention Device) and have it filled at an authorized LP
gas dealer by a qualified attendant.
gas dealer by a qualified attendant.
2)Make sure all of the grill control panel knobs are turned to
the “off” position and verify that the LP gas cylinder valve
is closed by turning the knob on the LP gas cylinder
clockwise until it stops.
is closed by turning the knob on the LP gas cylinder
clockwise until it stops.
3)Remove the protective cap from the LP cylinder gas
nozzle.
4)Hold regulator in a straight line with LP cylinder gas
nozzle so the connection does not cross thread.
5)Insert nipple of regulator into the LP cylinder nozzle
opening.
6)Hand tighten coupling nut in a clockwise direction. Do not
use tools.
7)Mix one cup of water with one cup of dishwashing liquid.
8) Open the valve on LP gas cylinder (Turn the knob on the
8) Open the valve on LP gas cylinder (Turn the knob on the
LP gas cylinder counter-clockwise.)
9)Check for leaks by brushing the soap solution on all LP
gas connections and fittings (such as those shown by the
heavy arrows in the diagram below.) Make sure you
generously brush the locations with the soap solution,
completely surrounding the connections and fittings.
heavy arrows in the diagram below.) Make sure you
generously brush the locations with the soap solution,
completely surrounding the connections and fittings.
10)If “growing” bubbles appear on any of the connection
points, then you have detected a gas leak. Immediately
close the LP cylinder valve by turning the handle
clockwise.
close the LP cylinder valve by turning the handle
clockwise.
A) If leak appears at either end of hose and regulator
assembly, retighten the connection at the leak, but do
not overtighten. (Note: Only hand tighten at coupling
nut) Repeat Leak Test.
not overtighten. (Note: Only hand tighten at coupling
nut) Repeat Leak Test.
B) If the leak is coming from the LP gas cylinder, from the
valves at the control knobs, or if the leak cannot be
stopped, do not use the grill. Call Customer Service at
1-800-251-7558.
stopped, do not use the grill. Call Customer Service at
1-800-251-7558.
11)Turn all control knobs to the “off” position and turn the
handle on the LP gas cylinder clockwise until it stops.
Disconnect LP gas cylinder by turning coupling nut on
regulator in a counter-clockwise direction until regulator is
released from threaded LP cylinder gas nozzle.
Disconnect LP gas cylinder by turning coupling nut on
regulator in a counter-clockwise direction until regulator is
released from threaded LP cylinder gas nozzle.
12)Place the protective cap over LP cylinder gas nozzle.
· Before proceeding, make certain that you
understand the Important Safeguards on pages 2
through 4 of this manual.
through 4 of this manual.
· Before lighting the LP gas grill, you must open
the the hood to prevent an explosion from
gas build-up.
gas build-up.
· If your LP gas grill catches on fire:
- If the fire is in the grill portion and you can safely
reach the control knobs on the control panel, then
turn them to the off position.
turn them to the off position.
- If the fire involves one of the hoses, and you can
safely reach the LP cylinder valve, shut the valve
off.
off.
- If the fire involves the cylinder, leave it alone,
evacuate the area and call the fire department.
- If there is any type of fire that threatens either
personal safety or endangers property, call the
fire department.
fire department.
· If you notice grease or other hot material dripping
from the grill onto the valve, hose, or regulator, turn
off the gas supply immediately. After the grill has
cooled, determine the cause and correct it. After
cleaning the valve and hose and regulator assembly,
perform a leak test before continuing use. (See Step
10 of Assembly Instructions)
off the gas supply immediately. After the grill has
cooled, determine the cause and correct it. After
cleaning the valve and hose and regulator assembly,
perform a leak test before continuing use. (See Step
10 of Assembly Instructions)
· Do not operate an LP gas grill if you have knowledge
of or suspect a gas leak.
· Never allow children to operate or play near an LP gas
grill. Do not leave grill unattended.
· Always turn off the LP gas cylinder at the LP cylinder
valve when not in use. Allow grill to cool before
handling parts or cleaning.
· Do not move an LP gas grill when in use or hot.
· Never touch hot surfaces. Use heat resistant gloves,
· Never touch hot surfaces. Use heat resistant gloves,
long-handled tongs, or cooking mitts at all times
since the grill will become very hot. Open the hood
carefully when cooking to avoid from the hot air and
since the grill will become very hot. Open the hood
carefully when cooking to avoid from the hot air and
steam trapped inside.
· Do not wear loose clothing (example: hanging
shirt tails, clothing with frills, etc.) around a LP
gas grill while in use or hot.
· Never lean your body over the LP gas grill when
lighting it or while it is in use or hot.
·
This LP gas grill is not designed to be used with
a solid plate (griddle.) Full coverage of plates will
cause excessive heat and could damage the grill.
Leak Testing
OPERATING THE LP GAS GRILL
30