Broilmaster BRB-1 ユーザーズマニュアル
Page 4
B101502-1-0311
l
OcatiOn
, c
OnnectiOns
,
anD
s
aFety
Built-In Kit Location
Built-In Kits are designed for outdoor use ONLY.
This Built-In Kit is designed for use with all P3 and T3 Model
This Built-In Kit is designed for use with all P3 and T3 Model
Broilmaster
®
gas grills and cannot be used with any other
grill or in any other capacity.
Never install or operate your Built-In Kit in any building,
Never install or operate your Built-In Kit in any building,
garage, or other enclosed area.
For your safety, the Built-In Kit should not be installed or
For your safety, the Built-In Kit should not be installed or
operated under any combustible materials, such as carports,
covered porches, awnings, or overhangs.
Never install or use your Built-In Kit in or on any recreational
Never install or use your Built-In Kit in or on any recreational
vehicle or boat.
CAUTION: THE INSTALLATION AND OPERATION OF
CAUTION: THE INSTALLATION AND OPERATION OF
THIS BUILT-IN KIT AT CLEARANCES LESS THAN
SPECIFIED BELOW MAY LEAD TO THE POSSIBILITY OF
FIRE, PROPERTY DAMAGE, OR PERSONAL INJURY.
A minimum clearance of twenty-four (24”) inches is required
A minimum clearance of twenty-four (24”) inches is required
from all sides of the island to any combustible material.
Examples of combustible materials are patio furniture,
Examples of combustible materials are patio furniture,
fences, or the outside of your home.
The area surrounding the built-in kit should be clear to ensure
The area surrounding the built-in kit should be clear to ensure
proper ventilation. Do not obstruct the flow of combustion
and ventilation air in any way. The ventilation openings on
the enclosure must also remain free and clear of debris.
WARNING: DO NOT INSTALL OR OPERATE THIS BUILT-
WARNING: DO NOT INSTALL OR OPERATE THIS BUILT-
IN KIT WHERE GASOLINE OR OTHER FLAMMABLE
MATERIALS ARE USED OR STORED. FAILURE TO
COMPLY WITH THIS WARNING COULD RESULT IN
EXPLOSION OR FIRE CAUSING PROPERTY DAMAGE
OR PERSONAL INJURY.
Connection Requirements
CAUTION: NEVER USE LIQUID PROPANE GAS IN A
GRILL DESIGNED FOR NATURAL GAS, OR NATURAL
GAS IN A GRILL DESIGNED FOR LIQUID PROPANE
GAS. QUESTIONS REGARDING DIFFERENT TYPES OF
GASES SHOULD BE DIRECTED TO YOUR LOCAL GAS
COMPANY.
Installation must conform to local codes or, in the absence
Installation must conform to local codes or, in the absence
of local codes, with the National Fuel Gas Code, ANSI
Z223.1. In Canada, installation shall be in accordance with
CAN/CGA-B149.2 Propane Installation Code, or CAN/
CGA-B149.1 Natural Gas Installation Code, and local
codes where applicable. Consult your local gas company or
Propane gas dealer for code regulations and recommended
procedures.
Broilmaster
Broilmaster
®
gas grills and side burners are NOT equipped
with pressure regulators. Your Nat. gas grill operates at a
manifold pressure of seven (7”) inches water column.
CAUTION: THE GRILL AND ITS INDIVIDUAL SHUTOFF
VALVE MUST BE DISCONNECTED FROM THE GAS
SUPPLY PIPING SYSTEM DURING ANY SYSTEM
PRESSURE TESTING AT TEST PRESSURES IN EXCESS
OF 1/2 PSIG.
Checking for Gas Leaks
CAUTION: DO NOT USE AN OPEN FLAME TO CHECK
FOR LEAKS. CHECKING FOR LEAKS WITH AN
OPEN FLAME MAY LEAD TO A FIRE OR EXPLOSION,
RESULTING IN PROPERTY DAMAGE OR PERSONAL
INJURY.
Using the following steps, check for gas leaks during initial
Using the following steps, check for gas leaks during initial
use and each time your Broilmaster
®
gas grill or side burner
is connected to gas or is connected to a cylinder that has
not been used recently
1. Using dish washing detergent and water, make a soapy
1. Using dish washing detergent and water, make a soapy
solution.
2. Turn OFF the knob on both the grill and side burner’s
control panel.
3. Turn ON the gas at the supply. A hissing sound indicates
a leak. Turn OFF the gas and repair all leaks.
4. If no hissing occurs, apply the soapy solution to all gas
connections.
5. Look for bubbles. Bubbles indicate a leak.
6. If there are bubbles, turn OFF the gas and repair all
6. If there are bubbles, turn OFF the gas and repair all
leaks.
7. Turn the gas ON and repeat the above procedure until
all leaks are repaired.