Aussie Bonza Deluxe ユーザーズマニュアル
· Open Lid or Hood (depending on the
model) before lighting the grill to prevent an
explosion from gas build-up.
explosion from gas build-up.
· The Lid (Kanga™ series only) must never be
covering the cooking surface while the LP gas
grill is in use or hot.
grill is in use or hot.
· Always inspect the gas hose and regulator
assembly
before each use. If the hose is cut, damaged, or
showing signs of excessive abrasion or wear, do
not use the LP gas grill.
showing signs of excessive abrasion or wear, do
not use the LP gas grill.
Contact the manufacturer, as the hose must be
replaced with an assembly specified by the
manufacturer prior to further use of the LP gas
grill.
replaced with an assembly specified by the
manufacturer prior to further use of the LP gas
grill.
How to manually light your LP gas grill
1) Open Lid or Hood (depending on the model)
2) Important: The LP gas cylinder valve must be
1) Open Lid or Hood (depending on the model)
2) Important: The LP gas cylinder valve must be
opened first before turning the control knobs on the
grill. Turn the handle on the LP cylinder valve counter-
clockwise until it stops.
grill. Turn the handle on the LP cylinder valve counter-
clockwise until it stops.
3) Insert a lit match through one of the match-lighting
holes underneath the front control panel on the grill.
(See figure below).
(See figure below).
4) Locate the control knob that corresponds to the match
lighting hole that you are using. Push in and turn the control
knob counter-clockwise until a click is heard.
knob counter-clockwise until a click is heard.
WARNING: If the burner fails to ignite after
following the above procedure, turn all the knobs to
the off position and close the valve on the LP cylinder.
Wait five minutes and repeat all of the above manual
lighting procedures. If the grill still fails to light, see
the Troubleshooting page.
the off position and close the valve on the LP cylinder.
Wait five minutes and repeat all of the above manual
lighting procedures. If the grill still fails to light, see
the Troubleshooting page.
5) Light the remaining burners from left to right by turning the
control knob counter-clockwise. Your grill has a crossover
ignition system that allows the burners to light successively
off one another. Confirm each burner is lit before
lighting another burner.
ignition system that allows the burners to light successively
off one another. Confirm each burner is lit before
lighting another burner.
6) After ignition, burners should be burned at the high position
for 3-5 minutes in order to preheat the grill. This process
should be done before every cooking session. The hood
(Bonza™ series only) should be closed during
preheating. The lid (Kanga™ series only) must never
be covering the cooking surface while the grill is in
use or hot.
should be done before every cooking session. The hood
(Bonza™ series only) should be closed during
preheating. The lid (Kanga™ series only) must never
be covering the cooking surface while the grill is in
use or hot.
WARNING: If a burner goes out during the cooking
cycle, turn all knobs to the off position and close the
valve on the LP cylinder. Open hood (BonzaTM series
only) and wait five minutes before attempting to relight
only) and wait five minutes before attempting to relight
the grill.
Manual Lighting of the Grill
29
4. Push in and turn control
knob counter-clockwise to
the “High” position. (Note
a click may be heard)
knob counter-clockwise to
the “High” position. (Note
a click may be heard)
3. Match lighting hole in left side of
grill body - Insert a lit match through
the match lighting hole.
grill body - Insert a lit match through
the match lighting hole.
2. Turn LP cylinder han-
dle counter-clockwise -
dle counter-clockwise -
1. Open lid or
hood (depending
on model)
hood (depending
on model)