Sharp R-1482 ユーザーズマニュアル

27

1. Disconnect the power supply cord, and uncoil the power

supply cord.

2. Remove the turntable tray and support from the oven cavity.
3. Remove the one (1) screw holding the exhaust  damper

assembly to the rear stay, and remove the exhaust
damper assembly by sliding it backward.

4. Remove the two (2) screws holding the oven (outer case

cabinet) to the top cabinet.

5. Remove the hood exhaust louver referring to "HOOD

EXHAUST LOUVER REMOVAL".

6. While supporting the front of the oven, unfasten the two

(2) unit mounting screws holding the oven to the unit
mounting plate.

7. Remove the oven by sliding it into the arms of the unit

mounting plate and pull the power cord out of the wall
cabinet.

8. The oven is now free and can be placed on the work

surface selected for servicing the oven.

9. Installation is the reverse of this procedure.

Remove the oven from the wall and proceed as follows;
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove one (1) screw holding the hood exhaust louver

to the oven, and pull it forward to remove by pushing the
right and left tabs of the hood exhaust louver. (Refer to
procedure of  "HOOD EXHAUST LOUVER REMOVAL".)

4. Remove four (4) screws holding the rear stay to the hood

fan motor or the oven, and remove it.

5. Remove the four (4) screws from the rear of the outer

case cabinet.

6. Slide the outer case cabinet back about 1 inch (3 cm) to

free it from retaining clips on the cavity face plate.

7. Disconnect the three (3) pin connector of the power

supply cord from the wiring harness and remove the
power supply cord together with the outer case.

8. Discharge high voltage capacitor.
CAUTION: 1. DISCONNECT OVEN FROM POWER

SUPPLY BEFORE REMOVING OUTER
CASE.

2. DISCHARGE THE HIGH VOLTAGE

CAPACITOR BEFORE TOUCHING ANY
OVEN COMPONENTS OR WIRING.

1. Disconnect the power supply cord, remove the oven

from wall, and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and  "Outer Case Removal".)
And proceed as follows.

2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove one (1) screw holding the hood duct to the oven

cavity front flange.

5. Disconnect the stop switch harness from the chassis

support and disconnect the wire leads from the fan motor.

6. Lift up the fan motor side of the hood duct.
7. Disconnect filament leads of transformer from the

magnetron and capacitor.

8. Disconnect high voltage leads of capacitor from the

transformer.

9. Disconnect wire leads from transformer.
10.Remove two (2) screws holding the transformer to right

base plate.

Re-install
1. Install by sliding the transformer on the right base plate

with its primary terminals toward the outer case.

2. Secure the transformer with two (2) screws to right base

plate.

3. Re-connect wire leads (primary and high voltage) to the

transformer and filament leads of transformer to
magnetron and high voltage capacitor. Refer to
"PICTORIAL DIAGRAM".

4. Re-install the hood duct holding the fan motor to the oven

cavity front flange with one (1) screw.

5. Reconnect the wire leads to the chassis support and the

fan motor, referring to "PICTORIAL DIAGRAM".

6. Re-install the outer case and check that oven is operating

properly.

CAUTION: MAKE SURE THE WIRE LEADS NEVER

TOUCH THE FAN BLADE.

4. Pull the hood exhaust louver from the oven cavity by

pushing the right and left tabs of the hood exhaust louver

to remove.

5. Now, the hood exhaust louver is free.

1. Disconnect the power supply cord and remove the oven

from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")

2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the 6-pin connector of the hood fan motor

from the main wire harness located at the right edge of
the hood duct and release the snap band from the hood
duct.

5. Remove the hood fan motor  from the hood duct by lifting

it up.

6. Now, the hood fan motor is free.
7. Remove  one (1) screw holding the hood duct to the oven

cavity front plate.

8. Release the 6-pin connector and the 3-pin connector of

the main harness A from the hood duct.

9. Disconnect the wire leads from the fan motor and chassis

support, and release the wire leads from holes of the