Sharp R-1482 ユーザーズマニュアル

30

1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove the three (3) screws holding the base cover to

the oven cavity

4. Remove the base cover from the oven cavity by pulling

REMOVAL")

4. Lift the oven lamp cover up.
5. Now, the oven lamp and the socket are found.
6. Screw the oven lamp off from the lamp socket.
7. Now, the oven lamp is  free.

down and moving to the left slightly.

5. Disconnect the wire leads from the  turntable motor.
6. Remove two (2) screws holding turntable motor to the

oven cavity.

7. Now the turntable motor is free.

1. Disconnect the power supply cord and remove the oven

from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and Outer case Removal")

2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood fan motor and the hood duct from the

oven cavity, referring to the procedure of " HOOD FAN
MOTOR, HOOD DUCT AND OVEN LAMP SOCKET
REMOVAL".

5. Disconnect the wire leads from the stirrer motor.
6. Remove the two (2) screws holding the stirrer motor to

the waveguide of the oven cavity.

7. Remove the stirrer motor from the waveguide.
8. Now, the stirrer motor is free.
9.  When installing the stirrer motor, the shaft of stirrer

motor must be inserted to the stirrer fan shaft. Refer to
the procedure of  "STIRRER COVER AND STIRRER
FAN INSTALLATION".

1. Put the stirrer fan on the stirrer cover to match the stirrer

fan shaft to the center of the stirrer support.

2. Insert the shaft of stirrer fan to the shaft of stirrer motor.
3. Insert the cutout of stirrer cover to the tabs on the ceiling.
4. Install the stirrer cover to the oven cavity, and secure it

by one canoe clip.

1. Disconnect the power supply cord.
2. Remove one (1) screw holding the hood exhaust louver

to oven cavity front flange.

3. Remove the hood exhaust louver from the oven by

pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of "HOOD EXHAUST LOUVER

1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove one (1) screw holding the hood exhaust louver

to oven cavity front flange.

4. Remove the hood exhaust louver from the oven by

pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of "HOOD EXHAUST LOUVER
REMOVAL")

5. Remove one (1) screw holding the control panel to the

oven cavity front  face plate.

6. Release the control panel from the oven cavity front face

plate by lifting it up.

7. Disconnect the wire leads from the relays RY1 and RY2.

8. Disconnect the connectors CN-A, CN-B, CN-E and CN-

F from the control unit.

9.  Remove the control panel assembly from the oven.
10.Now, the control panel assembly is free.
11.Disconnect the connector CN-G from the control unit.
12.Remove four (4) screws holding the control unit to the

key fixing plate.

13.Release the two (2) tabs holding the control unit to the

key fixing plate.

14.Now, the control unit is free.
15.Remove the one (1) screw holding the key fixing plate to

the control panel.

16.Release the four (4) tabs holding the key fixing plate to

Shaft

Stirrer Fan

Stirrer 
Cover

Canoe Clip

Stirrer Support

Shaft

Table

Center of
bracket

6. Install the hood duct to the oven cavity with the one (1)

screw.

7. Re-install the wire leads to the hole of the hood duct.
8. Connect the wire leads to the fan motor and chassis

support, referring to the pictorial diagram.

9. Refer to procedure of "OUTER CASE REMOVAL".  And

reverse their procedure. And re-install the outer case.